Louisville Tin and Stove W355F, W506, W502F W255F, W351F, W356F Safety Rules, Clearances, Controls

SAFETY RULES CONTROLS

A)The wall furnace should be located near the center of the house for best heat distribution.

B)Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

C)Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

D)Young children should be carefully supervised when they are in the same room as the appliance.

E)Do not place clothing or other flammable material on or near the appliance. Precautions should be taken so as not to place furniture, drapes, or other articles directly in front of grille or lower access door that would obstruct air openings as proper air flow is critical to proper operation of unit.

F)Any safety screen guard or casing front removed for servicing an appliance must be replaced prior to operating the appliance.

G)If the area where the appliance is to be installed contains carpeting, tile or combustible materials, other than wood flooring, the appliance shall be installed on a metal plate, a wood panel or other non- combustible materials. The use of ceramic or quarry tile is acceptable and will provide a surface that is easily cleaned. This material is to extend the full width and depth of the appliance.

CLEARANCES

As viewed from front of heater, the minimum clearance from cabinet to combustible construction: Side Wall – 1”; Floor – 2”; Ceiling – 11”.

In selecting a location for installation it is necessary to provide adequate accessibility clearances for servicing and proper operation. This appliance must not be connected to a chimney flue that serves to vent a solid-fuel burning (wood or coal) appliance, or a multi-vent system.

1” 11”

2”

All controls are preassembled at the factory. If integral snap-bulb type thermostat is used, make sure that sensing bulb is located on the bottom of gas valve with clips provided. DO NOT KINK the connecting tubing. Do not bend the capillary bulb.

The normal manifold pressure should be 3.5” w.c. on Natural Gas and 10” w.c. on L.P. Gas. The maximum inlet pressure in the gas supply pipe should never exceed 14” w.c. on L.P. Gas or 7.0” w.c. on Natural Gas.

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psig.

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psig.

The minimum inlet pressure in the gas supply pipe should be 5.0” w.c. on Natural Gas or 11” w.c. on L.P. Gas, “for purpose of input adjustment”.

The appliance is orificed at the factory for elevations up to 2,000 feet. If installed above 2,000 feet, the BTU input must be reduced 4% per 1,000 feet. See the following orifice chart for the proper orifice for a specific elevation. A blank orifice is shipped in the high altitude kit which will have to be drilled to correct size by installer, gas supplier or qualified serviceman.

NATURAL GAS

Model	0 to	2,000 -	4,000 -	6,000 -	8,000 –
No.	2,000’	4,000’	6,000’	8,000’	10,000’
W251F	43	44	45	47	48
W255F	43	44	45	47	48
W351F	36	38	40	41	43
W355F	36	38	40	41	43
	ORDER KIT #49820 45-1 HIGH ALTITUDE KIT
W501F	43	44	45	47	48
W505F	43	44	45	47	48
ORDER KIT #49850 2287-2 HIGH ALTITUDE KIT
		L.P. GAS
Model	0 to	2,000 -	4,000 -	6,000 -	8,000 –
No.	2,000’	4,000’	6,000’	8,000’	10,000’
W252F	1.45mm	54	54	55	55
W256F	1.45mm	54	54	55	55
W352F	52	52	52	53	54
W356F	52	52	52	53	54
ORDER KIT #49820 45-1 HIGH ALTITUDE KIT
W502F	1.45mm	54	54	55	55
W506F	1.45mm	54	54	55	55

ORDER KIT #49850 2287-2 HIGH ALTITUDE KIT

Page 3