Blue Background | Magnavox VRC602M specs

Blue Background 43

If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted.

Or, if you want to receive the weak signal, set BLUE BACK- GROUND to OFF. When you select a channel that is receiving a weak signal, you will see the static in the TV programming. The channel number will not appear on the screen when you select a weak channel, and you can not access the VCR’s status display.

Also, you may not be able to adjust the volume.1 To set BLUE BACKGROUND to ON or OFF, follow these

steps.

1

Press the VCR button, then press the MENU button.

SELECT op CHOOSE B

→PROGRAM VCR SET UP TUNER SET UP SET CLOCK

TO END PUSH EXIT

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

SELECT op CHOOSE B
→ REPEAT PLAY	OFF
ON SCREEN MODE
AUDIO OUT
LANGUAGE
BLUE BACKGROUND	ON
TO END PUSH EXIT

3

Press the PLAY/o button or the STOP/p button to select BLUE BACKGROUND. Then, press the F.FWD/B button repeatedly so that OFF (or ON) appears beside BLUE BACKGROUND.

SELECT op CHOOSE B

REPEAT PLAY	OFF
ON SCREEN MODE
AUDIO OUT
LANGUAGE

→BLUE BACKGROUND ON TO END PUSH EXIT

4

4 2-3

EJECT

POWER

MENU			STATUS/EXIT		CLEAR

1 2 3

4 5 6

7 8 9

MEMORYALT.CH

	0
REC	PAUSE
/OTR	/STILL

PLAY

REW F.FWD

STOP

CH.VOL.

	MUTE
VCR	TV	CBL/DBS
VCR/TV	SPEED	TIME SEARCH
	ENTER	SLOW

Press the STATUS/EXIT button.

Image 43

Magnavox VRC602M owner manual Blue Background

Contents

VCR For Customer Use Warranty Verification Declaration of Conformity FeaturesSafety Precautions Introduction Table of Contents VCR maintenance Putting Batteries in the Remote ControlBattery Safety Using the Remote Control Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Hookups Without a Cable Box/Direct Broadcast System cont’d Plug in the power cords of the TV and the VCR Connections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box/Direct Broadcast System cont’d Hookups with a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCR Press the VCR button, then press the Menu button Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Enter a 0 before a single-digit number Setting the Clock Press the VCR button, then press the Menu button Daylight-Savings Time Language Selection 2TV code Find your Setting the Remote to Operate a TV 2code Find your Cable BOX Codes Remote Control Buttons TV Button CHannel o/p Buttons If you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFF VCR Light VCR Display PanelCassette Compartment RECord Light Front Panel Rear Panel VHS Quasi Play Back Sqpb Playing Insert a tape with its record tab intact in the VCR Recording Recording One Channel/Watching Another One-Touch Recording Daily Timer Recording Timer Recording cont’d Tape Speeds Timer Recording cont’d Checking or Cancelling Timer Recordings Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Press the VCR button, then press the Time Search but- ton Time Search Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Automatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound System Multi-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound System Blue Background Helpful Hints Helpful Hints cont’d Renewed Specifications Glossary / SpecificationsGlossary Automatic Index Supplied Accessories