ENGLISH
REAR PANEL
z x | c v | b n | m |
nDIGITAL INPUT (Dig.1 - 4) / OUTPUT
(coaxial, optical)
These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 2 with optical jacks.
The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component.
⁄07.1 CHANNEL INPUT
By connecting a DVD Audio player, SACD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs.
⁄1Speaker outputs terminals
|
| VIDEO |
|
|
|
|
|
|
|
|
|
| S- |
|
|
|
|
|
|
|
|
|
|
|
|
| VIDEO |
FM (75Ω) | GND | AM | IN | OUT | IN | OUT |
|
| MONITOR | IN VCR1OUT | DVD | MONITOR | |
ANTENNA |
| DSS / VCR2 |
| VCR1 | DVD | TV | L | SL | C | SBL |
|
L
R
IN | OUT | IN | OUT | IN | OUT | IN | OUT |
|
| R | SR | SW SBR | 1 | 2 |
CD | TAPE | CDR/MD | DSS / VCR2 |
| VCR1 | DVD | TV |
| 7.1CH INPUT |
|
| |||
|
|
|
|
|
| AUDIO |
|
|
|
|
|
|
| |
| AUDIO |
|
|
|
|
|
|
|
|
|
|
|
| |
| PRE OUT |
|
|
|
|
|
|
|
|
|
|
|
| |
L | SL | C | SBL |
|
|
|
|
|
|
|
|
|
|
|
|
|
| R | L | R | L | R | L |
|
|
|
|
| FRONT | SURROUND BACK | SURROUND | CENTER | ||
R | SR | SW | SBR |
| S. SPEAKER B |
|
|
| |
|
|
| SPEAKER SYSTEMS 6 - 8 OHMS |
|
|
|
|
|
|
| COMPONENT VIDEO | |||
|
|
|
| |||
|
|
|
|
|
| Y |
IN | OUT |
|
|
|
|
|
|
|
|
|
|
| CB/PB |
|
|
|
|
|
| CR/PR |
OPT. | 3 | 4 | COAX. |
|
|
|
OUT |
|
| OUT | DVD | DSS / VCR 2 | MONITOR |
DIGITAL |
|
|
|
|
| |
|
|
|
|
| AC IN |
|
|
| AC OUTLET |
|
|
|
230V 50HZ
SWITCHED
100W MAX.
For digital output, there is 1 coaxial output and 1 optical output.
The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components.
mCOMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR4500. The SR4500 has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video
Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers.
Note:
•You can use surround back speaker terminals as S(Surround) SPEAKER B terminals, when you use no surround back speaker.
⁄2Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right).
⁄3⁄2 ⁄1
zAUDIO IN/OUT (CD, TAPE,
DVD, VCR1, DSS/VCR2)
These are the analog audio inputs and outputs. There are 7 audio inputs (4 of which are linked to video inputs) and 4 audio outputs (2 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The
audio inputs and outputs require
xFM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.
⁄0 . ,
cVIDEO IN/OUT (TV, DVD, VCR1, DSS/VCR2)
These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and
The 2 video output channels can be used to be connected to video tape recorders for making recordings.
The input signals of video and
vMONITOR OUT
This is a monitor output and each one includes both composite video and
bREMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with remote control
component and one component video output connector to output it directly into the matrix decoder of the display device.
By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail.
,AC IN
Connect to supplied an AC cable, and connect to an AC power outlet.
SR4500 has to be powered by 230V AC only.
.AC OUTLET
Connect the AC power cable of component such as a DVD or CD player to this outlet.
The marked SWITCHED provides power only when the SR4500 is turned on and is useful for components which you use every time you play your system.
Caution:
•In order to avoid potential
•The capacity of this AC outlet is 100W. Do not connect devices that consume electricity more than the capacity of these AC outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.
Use these jacks for connection to external power amplifiers.
⁄3Subwoofer Output
Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with
a2 channel subwoofer amplifier, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier.
6