Marantz SR5600 Other Function, Tv Auto On/Off Function, Attenuation To Analog Input Signal, Notes

OTHER FUNCTION

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV-VIDEO in jack to control the power (ON/ OFF) to the SR5600.

ATTENUATION TO ANALOG INPUT

SIGNAL

T-MODE RDS F.DIRECT

INPUT/DISC+ AUDIO SUB-T/ATTPTY

CH.SEL LIP.SYNC

SYSTEM REMOTE CONTROLLER

RC5500SR

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual sounds heard from the speakers.

When headphones are used, the MENU button automatically switches to the Dolby headphone mode.

The OSD that appears when the MENU button is pressed is shown below.

selecting the “VIDEO OFF” setting.		ENGLISH
VIDEO ON/OFF
When no video signal is connected to the SR5600
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
To select video off, press the AMP button and
press the V-OFFbutton.
TUNER CD	TAPE CDR/MD

AUTO POWER ON

1. Be sure the TV auto mode is ENABLED. (Refer page 19 : System Setup)

2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input.

3. Turn OFF the power to the TV TUNER and the SR5600.

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the remote.

“ATT” indicator will be illuminated when this

HEAD PHONE

DOLBY HP MODE	: BYPASS
SURROUND	: ✽✽✽
L LEVEL	: 0dB
R LEVEL	: 0dB

R5600

SURROUND

DIGITAL

AAC

	AUX1	AMP
TV			MAIN
VOL.	SLEEP	MUTE	VOL.
OSD		MENU
NIGHT	CSII	EX/ES	VIRTUAL
	4	5	6
DISPLAY	MCH-ST	STEREO	7.1CH IN
	7	8	9
CLEAR	MEMO	A/D	P.SCAN/V-OFF
		0

CHANNEL/SKIP

4. Turn ON the TV TUNER and tune in a receivable station.

5. When the station is received, the SR5600 turns ON and TV is selected automatically.

function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD- OUT, VCR1-OUT and DSS/VCR2-OUT.

This function is memorized for each individual

DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons.

BASS TREBLE TUNE/SEARCH

AUTO POWER OFF

1. In the above situation, turn the TV TUNER

input source.

BYPASS → DH1 → DH2 → DH3 → BYPASS

BYPASS : Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo.

DISPLAY MODE

SR5500

SET UP/		MENU OFF
T.TONE
PURE DIRECT	AUTO		DTS
	1	2	3
NIGHT	CSII	EX/ES	VIRTUAL

OFF or select a channel that does not contain any broadcast.

2. The power to the SR5600 switches to STANDBY after approx. 5 minutes.

Notes:

LISTENING THROUGH HEADPHONES	DH1 : The size of a typical living room space
This jack may be used to listen to the SR5600’s	is simulated.
output through a pair of headphones. Be certain	DH2 : The expansiveness of a structure as
that the headphones have a standard 1/4” stereo	large as a music hall is simulated.
phono plug . (Note that the speakers will	DH3 : A large space such as that found in a

SURROUND

DIGITAL

AAC

4	5	6
DISPLAY MCH-ST	STEREO	7.1CH IN

7 8 9

CLEAR MEMO A/D P.SCAN/V-OFF

0

CHANNEL/SKIP

BASS TREBLE TUNE/SEARCH

T-MODE RDS F.DIRECT

•AUTO POWER OFF is canceled if the SR5600 is set to a source other than TV.

The function reactivates when TV is selected again.

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.

•The S-Video terminal does not support “TV AUTO ON/OFF” function.

automatically be turned off when the headphone	movie theater is simulated.
jack is in use.)
	When the PURE DIRECT mode is selected, Dolby
AV SURROUND RECEIVER SR5600	surround processing is bypassed and “✽✽✽” is
	displayed as the mode indication.
	The surround mode can be selected when any of
	the modes in DH1, DH2, or DH3 is selected.
	L/R LEVEL can be set in the ±10 dB range.

You can select the display mode for the front display of the SR5600.

To select this mode, press the DISPLAY on the remote control.

When this button is pressed, the display mode is switched in the following sequence.

→ Surround Mode → Auto-display Off → Display

Note:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

Notes:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

•TONE cannot be set when any of the modes in DH1, DH2, or DH3 is selected.

•The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input.

Off → Input Function → Surround Mode....

In Auto display off mode, the display is off. But, if

you make a change to the unit such as input or

surround mode, the display will show that change,

then go back to off after about 3 seconds. When

changing the volume, it is not displayed.

In Display off mode, the display is off completely.

Note:

•Only the DISP indicator will be illuminated on the front display in display off condition

27