Marantz SR5600 manual AUX2 Input, Lip.Sync, Listening to the Tuner

1. Select a desired Video source to decide the routed video signal to the Monitor Outputs .

2. Press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote to switch the 7.1 channel input.

3. If it is necessary to adjust the output level of each channel, press the CH.SEL button on the remote.

Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between –10 to +10 dB. The subwoofer can be adjusted between –15 and +10 dB.

These adjustments result will be stored to 7.1 CH. INPUT memory.

4. Adjust the main volume with the MAIN VOLUME knob or the VOL buttons on the

remote.

To cancel the 7.1 CH. INPUT setting, press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote.

Notes:

• When the 7.1 CH. Input is in use, you may not

AUX2 INPUT

If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder,

L(front left) and R (front right) inputs terminals are available as AUX2 input.

In this case, You can connect additional audio source to AUX2 as other audio input terminals.

AV SURROUND RECEIVER SR5600

LIP.SYNC

Depending on the image device (TV, monitor, projector, etc.) connected to the SR5600, a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the SR5600 to correct the time lag between the sound and image. It can be operated

BASIC OPERATION

(TUNER)

LISTENING TO THE TUNER

Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country’s standard is 9 kHz step, Press TUNER button on the remote more than 6 seconds. Scan step will change.

Note:

•Preset memory for the tuner will clear by changing this setup.

AUTO TUNING

2.	1.		TV	VCR1	DSS/VCR2	DVD
		1.	TUNER	CD	TAPE	CDR/MD
				AUX1	AMP
			TV			MAIN
			VOL.	SLEEP	MUTE	VOL.

SURROUND
DIGITAL
AAC
CLEAR	MEMO	A/D	P.SCAN/V OFF
		0
		CHANNEL/SKIP

2.	BASS	TREBLE	TUNE/SEARCH
		T-MODE	RDS	F.DIRECT
	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY

MANUAL TUNING

2.	1.		TV	VCR1	DSS/VCR2	DVD
		1.	TUNER	CD	TAPE	CDR/MD
				AUX1	AMP

	TV			MAIN
SURROUND	VOL.	SLEEP	MUTE	VOL.
DIGITAL
AAC

	CLEAR	MEMO	A/D	P.SCAN/V OFF
			0
			CHANNEL/SKIP
2.	BASS	TREBLE	TUNE/SEARCH
		T-MODE	RDS	F.DIRECT
	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY

(Using the SR5600)

1. To select tuner and desired band (FM or AM), press the BAND button on the front panel

2. Press the or cursor buttons on the front panel to select the desired station.

(Using the remote control unit)

1. To select tuner and desired band (FM or AM), press the TUNER button twice within in two seconds on the remote.

2. Press the 5 or 6 on the remote to tune in the desired station.

DIRECT FREQUENCY CALL

PURE DIRECT AUTO DTS

ENGLISH

select a surround mode, as the external decoder

determines processing.

• In addition, there is no signal at the record outputs

when the 7.1 CH. Input is in use.

with the “LIP.SYNC” and and cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.

Note:

(Using the SR5600)

1. To select tuner and desired band (FM or AM), press the BAND button on the front panel.

2. Press the or cursor buttons on the front panel for more than 1 second to start the auto tuning function.

3. Automatic searching begins then stops when

	POWER
	TV	VCR1	DSS/VCR2	DVD
1.	TUNER	CD	TAPE	CDR/MD
		AUX1	AMP
	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.

3.		1	2	3
	NIGHT	CSII	EX/ES	VIRTUAL
		4	5	6
	DISPLAY	MCH-ST	STEREO	7.1CH IN
		7	8	9
	CLEAR	MEMO	A/D	P.SCAN/V-OFF
			0

CHANNEL/SKIP

BASS TREBLE TUNE/SEARCH

2.		T-MODE	RDS	F.DIRECT
	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY

•The LIP.SYSNC feature turns OFF (0 ms) in the PURE DIRECT mode. When the PURE DIRECT mode is deactivated, the set value of the LIP.SYSNC feature is automatically restored.

a station is tuned in.

(Using the remote control unit)

1. To select tuner and desired band (FM or AM), press the TUNER button twice within in two seconds on the remote.

2. Press the 5 or 6 for more than 1 second on the remote.

3. Automatic searching begins then stops when a station is tuned in.

If tuning does not stop at the desired station, use to the “Manual tuning” operation.

CH.SEL LIP.SYNC

OSDMENU

SYSTEM REMOTE CONTROLLER

1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.

2. Press the F.DIRECT on the remote, display will show “FREQ - - - -”.

3. Input your desired station’s frequency with the numeric buttons on the remote.

4. The desired station will automatically be tuned.

29