REAR PANEL CONNEC - TIONS (SEE PAGE iii.)
All connections to the rear panel should be made with the entire system powered off.
To avoid errors, it is advisable to connect one cable at a time between the various components.
aFM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”.
The supplied AM loop antenna will provide good AM reception in most areas.
Position the loop antenna until you hear the best reception.
sPRE OUT jacks
Jacks for Front - L/R,
dSUB WOOFER output jack
Connect to the input jack(s) of the power amplifier for subwoofer channel or powered subwoofer.
fAnalog AUDIO outputs for audio
recording equipment
TAPE and
Connect each output to the audio inputs (REC in) of your recording equipment.
gAnalog AUDIO inputs
CD, TAPE, and
Connect the audio outputs of your source components to the input jacks on the receiver.
hVIDEO
VCR1, and DSS/VCR2
Connect each output to the video input (REC in) of your video recording equipment.
jTV MONI.
Connect the TV MONI jack to your TV’s video input (VIDEO IN) jack. You can connect your video equipment with
You must use the same type of connection from your video player into the receiver, and out of the receiver into your TV.
Both must be composite video or both must be
kSPEAKER SYSTEMS terminals
SPEAKER SYSTEMS A TERMINALS
FRONT Left & Right speakers output terminals
Connect to the front left & right speakers.
CENTER speaker output terminals
Connect to the center speaker.
SURROUND Left & Right speakers output terminals
Connect to the surround (rear) left & right speakers.
SURROUND Center speaker output terminals
Connect to the surround center speaker.
SPEAKER SYSTEMS B TERMINALS
FRONT Left & Right speakers output terminals
Connect to the front left & right speakers.
Notes:
•When you use the speaker systems A and B simultaneously, the connected speakers which are impeadance 12 to 16 ohms must be used.
l6.1 CH INPUT jacks
Connect to the outputs of DVD Audio player, SACD Multi channel player or an external multichannel decoder.
¡0DIGITAL outputs
Optical and Coaxial
Connect to the digital input of your digital recording equipment.
¡1DIGITAL inputs
Dig.1,2 (Optical) and Dig. 3, 4, 5 (Coaxial)
Connect each input to the digital output of your source equipment. Use the SETUP MAIN MENU to assign digital input to appropriate source. (see page 16)
Note :
•The coaxial connections are not for
¡2REMOTE CONTOROL IN/OUT terminals
Connect to a Marantz component equipped with remote control (RC- 5) terminals.
¡3Analog AUDIO outputs for video recording equipment
VCR1, and DSS/VCR2
Connect each output to the audio inputs (REC in) of your video recording equipment.
¡4Analog AUDIO inputs for video source equipment
TV, DVD, VCR1, and DSS/VCR2
Connect each input to the audio outputs of your video source equipment.
¡5VIDEO inputs
TV, DVD, VCR1, and DSS/VCR2
Connect each input to the video outputs of your video source equipment.
TV, DVD, VCR1, and DSS/VCR2
Connect each input to the
¡7AC OUTLET
Connect the power cables of components such as a DVD and CD player to these outlets. Both SWITCHED and UNSWITCHED outlets are provided.
The one marked SWITCHED provides power only when the SR6300 is turned on and is useful for components which you use every time you play your system.
The one marked UNSWITCHED is always live as long as the SR6300 is plugged into a live outlet.
A component connected here may be left on permanently, or may be switched off with its own power switch.
Caution:
•In order to avoid potential
•The capacity of this AC outlet is 120W. Do not connect devices that consume electricity more than the capacity to this AC outlet. If total power consumption of connected devices exceeds the capacity, protection circuit shuts down the power supply.
¡8Power Cable
Connect to AC power outlet.
SR6300 can be powered by 120V AC only.
ENGLISH
5
