Marantz SR6300 manual REMOTE CONTROLER RC7300SR, English

ENGLISH

REMOTE CONTROLER RC7300SR

NAMES AND FUNCTIONS

zInfrared window

Outputs and inputs an infrared control signals.

xLCD (Liquid Crystal Display)

Used to display information about currently selected functions.

c/ (open/close) button

Used to open or close the door.

vSource POWER ON/OFF button

Used to turn specific sources (such as DVD players, etc.) ON and OFF independently from the rest of the system.

bEQ button

Used to turn on or off HT (Home Theater)-EQ mode when the surround mode is set as AUTO, DOLBY, DTS or STEREO.

This mode compensates for the audio portion of a movie sounding “bright”. When this button is pressed, “HT-EQ” indicator lights up.

nV-OFF (video off) button

Used to turn off the video signal.

Note:

• This button is unavailable for SR6300.

mDVD operating buttons

(when DVD mode is selected)

AUDIO button

Used to select one of the audio language.

ANGLE button

Used to change the different camera angle.

SUBTITLE button

Used to select one of the subtitle language.

,Numeric buttons 1 to 9, 0 / Surround

mode buttons

Numeric buttons

Used to enter figures in the selection of a tuner preset station and sta- tion name preset or to set select a CD track number, etc. The functions of these buttons are dependent on the function button selected.

Surround mode buttons (when AMP mode is selected)

Used to select the surround mode.

.CL (clear) / S-DIRECT (source direct)

button

Used to cancel for certain memory or programming operations.

(when AMP mode is selected)

Used to select the S-DIRECT (source direct) mode. In source direct mode, the tone control circuitry is bypassed.

⁄0INPUT button

Used to select monitor input.

⁄1T.MODE button

(when TUNER mode is selected)

Used to select the auto stereo mode or mono mode when the FM band is selected.

The “AUTO” indicator lights in the auto stereo mode.

⁄2(TV) CH 3/4 buttons

Used to increase or decrease the TV channel.

⁄3TOP MENU button

(when DVD mode is selected)

Used to call up the top menu of the DVD.

⁄4Tone / Deck cotrol buttons

Tone cotrol buttons (when AMP mode is selected)

The TREBLE buttons are used to adjust the tone control of high fre- quency sound for left and right speaker.

The BASS buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.

Deck cotrol buttons (when Tape mode is selected)

The DECK A button are used to select the deck A.

The DECK B button are used to select the deck B.

The 1 2 button are used to change the direction.

⁄5CURSOR / OK button

Used to operate on-screen and other displays used by receivers and other components.

⁄6CH SEL. (channel select) button

(when AMP mode is selected)

Used to call up SETUP MAIN MENU and adjust speaker levels or 6.1 ch input level.

⁄7SETUP button

(when DVD mode is selected)

Used to call up the setup menu of the DVD.

⁄8CONTROL buttons

These buttons are used when operating the CD player, TAPE deck, etc. The function of these buttons are dependent on the function button selected.

(when AMP mode is selected)

SPK A/B button

Speaker mode is switched in the following sequence. A → B → A+B → off

ATT button

When the input signal is too high and the voice distorts even by throt- tling the SR6300 VOLUME control, turn on this function. “ATT” is indi- cated when this function is activated.

The input level is reduced. Attenuator is invalid for use with the output signal of “REC OUT”.

Note:

• This function is unavailable during the digital input is selected.

MULTI button

This button is unavailable for SR6300.

⁄9Input selector buttons/ FUNCTION SE-

LECTOR buttons (AUDIO/VIDEO INPUT)

Used to switch the remote controller to the command sets for specific sources (amplifier, receiver, etc.), thereby allowing a single remote controller to control up to 11 different components. To use these buttons to switch the amplifier’s source, press the desired button twice within 2 seconds. The AMP button ⁄9is used only to switch command set of the remote controller itself and therefore does not transmit any signal. Further, the function buttons may also be programmed to execute macros. (A macro allows a complex string of operations to be performed in series simply by pressing a single button.) One button can be programmed to learn sequences containing up to 10 commands. The following is an example of such a sequence that can be activated automatically using a macro:

Turn the receiver ON → Switch the function to DVD → Set the Surround Mode to VIRTUAL → Set the DVD player to Play.

Note:

• The AUX2 button is unavailable for SR6300.

6