Configration
– Remote Control
Wireless: Set to use the included remote controller.
Standard 1
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking |
Config. |
| Auto Power Off | Enable | ||
| Trigger 2 | Full | On | |
| Trigger 2 | Normal | On | |
| Trigger 2 | Zoom | On | |
| Trigger 2 Through | On | ||
| Remote Control |
|
| |
|
|
| ||
Color Temp.Calibration
Reset Lamp Life
Reset All
Wired: | Set to control the projector from either Marantz’s AV components connected to the |
| REMOTE CONTROL IN/OUT terminals or a PC or other device connected to the RS- |
| 232C terminal of the projector. The included remote controller cannot be used in this case. |
When this item is selected, a confirmation message appears asking whether to change the currently selected mode to the other mode or not. To change the mode, select “Yes” and press the ENTER button on the projector. To keep the same mode, select ‘No” and press the ENTER button.
Notes:
-To prevent misoperation, the ENTER button of the remote controller does not respond to touch when the Wired/Wireless setting is displayed. Press the ENTER button of the projector to enter the setting.
-To change from Wired to Wireless, set “Wireless” from the menu using the buttons of the projector.
ENGLISH
Item | Adjustments | |
Auto Power Off | Enable, Disable | |
Trigger 2 Full | On, Off | |
Trigger 2 | Normal | On, Off |
Trigger 2 | Zoom | On, Off |
Trigger 2 | Through | On, Off |
Remote Control | Wireless, Wired | |
Color Temp. Calibration | Yes, No | |
Reset Lamp Life | Yes, No | |
Reset All |
| Yes, No |
– Color Temp. Calibration |
After replacing the lamp or in other cases where the |
lighting changes, color temperature can be adjusted |
using the color temperature sensor. For more information |
on how to adjust color temperature, see “Color |
Temperature Adjustment” (☞ P.26). |
– Reset Lamp Life |
If the lamp is replaced before reaching its 2000 hours |
lamp life, be sure to reset the lamp’s life counter. To do |
Color Temp. Calibration?
Yes |
| No |
|
|
|
–Auto Power Off
When the auto power off feature is set to Enable, power to the projector automatically shuts off if no signals are received and no operations are performed for about 10 consecutive minutes. If 9 minutes pass without the projector receiving any signals or being operated in anyway, the below message appears on the screen.
Auto Power Off
It will be standby mode soon.
this, select “Reset Lamp Life” from the Configuration |
menu. When the user selects this item, the following |
message appears: |
Select “Yes”, and press the ENTER button. Then the |
lamp life is initialized. |
– Reset All |
All settings are reset to the factory default settings except |
Reset Lamp Life ?
Yes |
| No |
|
|
|
About 1 minute after the message appears on the screen, power to the projector shuts off.
Note:
After the above message appears on the screen, pressing any button on the projector or remote control other than the 
/ I button on the projector and the ON or STANDBY buttons on the remote control resets the auto power off feature.
The auto power off feature will activate again if, after that, the projector goes without receiving any signals or being operated in anyway for 10 consecutive minutes.
–Tigger 2
Select either 12V output or 0V output by choosing On or Off for each aspect mode. Full, Normal, Zoom, and Through.
This allows you to control such as a powered dual aspect screen with the outputs for the aspect modes.
On: Output DC 12V.
Off: No output.
the lamp life. |
When the user selects this item, the following message |
appears: |
Select “Yes”, and press the ENTER button. |
Reset All ?
Yes |
| No |
|
|
|
23
