CLEAN FILTER
This oven displays CLEAN FILTER at user defined intervals. When the message displays Amana recommends cleaning the air filter thoroughly. Cleaning the air filter will not shut off the message. The message will stop displaying automatically after 24 hours. Depending on microwave use and environmental conditions, the filter may need to be cleaned more frequently. Once the frequency is determined, set the option
for the appropriate time frame.
7 Preprogrammed Pads
To cook food using preprogrammed cooking sequences:
1.Open oven door and place food in oven. Close door.
2.Press desired pad.
3.Oven begins to cook.
4.At end of cooking cycle oven beeps and shuts off.
QuickStartReferenceGuide
Refer to Product Safety Manual for Safety Statements
Complete Owner’s Manual available online
|
| Oven Wall Clearances |
|
| |
A |
| 2” (5.1 cm) of clearance around top of oven. For |
|
| International (50 Hz) models, allow at least 12” (30 |
| B | cm) of clearance around top of oven. Proper air |
| flow around oven cools electrical components. With | |
|
| |
C |
| restricted air flow, oven may not operate properly |
|
| and life of electrical parts is reduced. |
|
| |
|
| back of oven and back wall. |
|
| |
|
| of oven. |
So...how do I use it? (Electronic Control)
Manual Operation
To cook food using a specific entered time and power level:
1.Open oven door and place food in oven. Close door.
2.Press TIME ENTRY pad and enter cooking time.
3.Press a power level pad to change power level if desired (some models).
• COOK LEVEL displays with the power setting.
4.If stage cooking is desired, press TIME ENTRY pad and repeat steps 2 through 4, (some models).
5.Press START pad.
6.At end of cooking cycle oven beeps and shuts off.
QTY 2X
Programming
(some models)To change the cooking factor:
1.Open oven door.
2.Press and hold pad 1 for approximately 5 seconds.
3.Press pad to be reprogrammed.
4.Press the QTY 2X pad.
5.Press a numbered pad to change the cooking factor.
•Cooking factor can be set from 10% to 100%.
•Default is 80%.
•Pad 5 would change the cooking factor to 50%.
6.Press START pad to save changes.
Programming Items
1.Open oven door.
2.Press and hold pad 1 for approximately 5 seconds.
3.Press pad to be reprogrammed.
4.Enter cooking time by using the number pads.
5.Press a power level pad to change power level if desired.
6.If stage cooking is desired, press TIME ENTRY pad.
•Display briefly shows the stage number.
•Display changes to cook time and power level for the next stage.
7.Enter cook time and power level as in steps 4 and 5 (some models).
•To enter another cooking stage for that pad, press TIME ENTRY pad again.
•Up to four different stages can be programmed (some models).
8.Press START pad to set new programming changes to the pad.
NOTE: To discard changes, press STOP/RESET pad or close oven door.
QTY 2X Pad (some models)1.Open oven door and place food in oven. Close door.
2.Press QTY 2X pad.
3.Press desired preprogrammed pad or pad sequence.
4.Oven begins cooking. Displayed cooking time is the total of original cooking time and added 2X time.
The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under unfavorable voltage supply conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissible system impedance Zmax of 0.2 Ohms at the interface point of the user’s supply. The user has to ensure that this device is connected only to a power supply system which fulfills the requirement above. If necessary, the user can ask the public power supply company for the system impedance at the interface point.
16026795 | ©2006 Maytag Services |