6. Troubleshooting

 

Before you ask for repair service, check the following points:

 

 

 

 

 

 

 

 

 

State of Machine

Remote Controller

Cause

Troubleshooting

 

 

 

'” display is not lit up.

Power failure

Press the [ON/OFF] button after power restoration.

 

 

It does not run.

No display appears even

The power supply is turned OFF.

Turn the power supply ON.

 

 

when the [ON/OFF] but-

The fuse in the power supply is gone.

Replace fuse.

 

 

 

 

 

 

ton is pressed.

The earth leakage breaker is gone.

Put in the earth leakage breaker.

 

 

 

 

 

After checking the set temperature and inlet temperature

 

 

 

 

Improper temperature adjustment

on the liquid crystal display, refer to [Room temperature

 

 

Air flows out but it does

The liquid crystal display

 

adjustment], and operate the adjustment button.

 

 

 

Clean up the filter.

 

 

not cool enough or heat

shows that it is in the

The filter is filled with dust and dirt.

 

 

(Refer to [Caring for the machine].)

 

 

enough.

state of operation.

 

 

 

There are some obstacles at the air inlet and outlet of

Remove.

 

 

 

 

 

 

 

 

the indoor and outdoor units.

 

 

 

 

 

 

 

 

 

Windows and doors are open.

Close.

 

 

 

 

 

Wait for a while.

 

 

 

 

 

(To protect the compressor, a 3-minute restart-preventing

GB

 

 

The liquid crystal display

The restart-preventing circuit is in operation for 3 min-

circuit is built into the indoor unit. Therefore, there are occa-

 

Cool air or warm air

utes.

sions sometimes when the compressor does not start run-

 

 

 

 

shows that it is in opera-

 

 

does not come out.

 

ning immediately. There are cases when it does not run for

 

 

tion.

 

 

 

 

 

as long as 3 minutes.)

 

 

 

 

 

 

 

 

 

Indoor unit operation was restarted during the heating

Wait for a while.

 

 

 

 

and defrosting operation.

(Heating operation starts after ending defrosting operation.)

 

 

 

The “check” and check

There are some obstacles at the air inlet and outlet of

Rerun after removal.

 

 

It runs briefly, but soon

the indoor and outdoor units.

 

 

code flashes on the liquid

 

 

 

stops.

The filter is filled with dust and dirt.

Rerun after cleaning the filter. (Refer to [Caring for the ma-

 

 

crystal display.

 

 

 

chine].)

 

 

 

 

 

 

 

The sound of the ex-

 

When other indoor units are engaged in cooling opera-

 

 

 

haust and rotation of

All lights are out except

 

 

 

tion, the machine stops after running a drain-up mecha-

 

 

 

the motor can still be

the powered display of

Wait for 3 minutes.

 

 

nism for 3 minutes when air-cooling operation is

 

 

heard after stop of run-

'”.

 

 

 

stopped.

 

 

 

ning.

 

 

 

 

 

 

 

 

 

The sound of the ex-

 

When other indoor units are engaged in cooling opera-

 

 

 

haust and the rotation

All lights are out except

 

 

 

tion, drained water is brought in. If the drain water is

It soon stops. (If the noise occurs more than 2-3 times in an

 

 

of the motor can be

the powered display of

 

 

collected, the drain-up mechanism initiates a draining

hour, ask for repair service.)

 

 

heard intermittently af-

'”.

 

 

operation.

 

 

 

ter stop of running.

 

 

 

 

 

 

 

 

 

Warm air comes out in-

The liquid crystal display

When other indoor units are engaged in heating op-

 

 

 

termittently when the

It soon stops. (If the room temperature rises uncomfortably

 

 

shows that it is in the

eration, the control valves are opened and closed from

 

 

thermostat is OFF or

high in a small room, stop operation.)

 

 

state of operation.

time to time to maintain the stability of the system.

 

 

during fan operation.

 

 

 

 

 

 

 

 

 

 

 

 

If operation stops due to a power failure, the [restart-preventing circuit at power failure] operates and disables unit operation even after power restoration. In this case, press the [ON/OFF] button again and start operation.

If malfunctions persist after you have checked the above, turn the power supply OFF and contact your dealer with information about the product name, the nature of the malfunction, etc. If the display of “[check]” and (4 digit) check code flashes, tell the dealer contents of the display (check code). Never attempt to repair by yourself.

The following symptoms are not air conditioner failures:

The air blown out from the air conditioner can sometimes give off odors. This is due to cigarette smoke contained in the air of the room, the smell of cosmetics, the walls, furniture, etc., absorbed in the air conditioner.

A hissing noise can be heard immediately after the air conditioner is started or stopped. This is the sound of the refrigeration flowing inside the air conditioner. This is normal.

The air conditioner sometimes snaps or clicks at the beginning or end of cooling/heating operation. This is the sound of friction on the front panel and other sections due to expansion and contraction caused by temperature change. This is normal.

8

KB79K384H01_en.p65

8

08.1.22, 6:02 PM

Page 8
Image 8
Maytag P12, PEFY-P06, P15, P18, P24 NMSU-E, P08 Troubleshooting, Following symptoms are not air conditioner failures

P08, P24 NMSU-E, P18, P12, P15 specifications

The Maytag PEFY series, which includes models P06, P12, P18, P15, and P24, along with the NMSU-E, represents a significant advancement in the realm of heating and cooling solutions. Renowned for their reliable performance, these systems cater to both residential and commercial applications, ensuring optimal indoor comfort year-round.

One of the main features of the Maytag PEFY series is their exceptional energy efficiency. Equipped with advanced inverter technology, these units adjust their operating capacity based on the current demands of the space, minimizing energy consumption while maintaining a comfortable environment. This not only leads to lower utility bills but also reduces the carbon footprint, aligning with modern sustainability goals.

The PEFY series is designed with versatility in mind. These heat pump systems can efficiently switch between heating and cooling modes, making them an ideal choice for varying climate conditions. The multi-zone capability allows for tailored climate control in different rooms or areas, enhancing comfort while optimizing energy use. This is particularly beneficial for larger properties where different rooms may have different heating and cooling needs.

In terms of design, Maytag has ensured that the PEFY units are compact and unobtrusive. Their sleek profiles allow for easy installation in various settings, whether it be in a commercial space or within a home. The low noise operation is another hallmark feature, providing quiet comfort without disturbing occupants. This is complemented by a user-friendly interface that allows for effortless temperature adjustments and system monitoring.

The NMSU-E model builds on these features by incorporating advanced control technologies, including smart connectivity options. Users can remotely operate and manage their HVAC systems through smartphone applications, allowing for complete control of home or office comfort from anywhere. This integration with smart home ecosystems enhances convenience and adaptability.

Additionally, the PEFY series comes equipped with robust safety features, including refrigerant leak detection and automatic restart capabilities, ensuring continuous and safe operation. The durable construction materials used in the units provide added reliability and longevity, making them a sound investment for property owners.

In conclusion, the Maytag PEFY-P06, P12, P18, P15, P24, and NMSU-E models are distinguished by their energy efficiency, versatile heating and cooling capabilities, sleek design, and smart technology integration. They represent the future of HVAC solutions, providing comfort while addressing environmental concerns and user convenience.