5 | CYCLE OPTIONS | 6 | LED DISPLAY AND SETTINGS BUTTONS |
| Use these buttons to select available options for your dryer. |
| When you select a cycle, its default settings will light up and |
| Not all cycles and options are available on all models. |
| the Estimated Time Remaining (for Sensor Cycles) or actual |
| Wrinkle Prevent/Wrinkle Prevent with Steam |
| time remaining (for Timed Cycles) will be displayed. |
|
| Use the buttons along the bottom of the display to adjust | |
| (on some models) |
| |
|
| settings. See “Cycle Guide” for available settings on each | |
| If you will be unable to remove a load immediately, press |
| |
|
| cycle. Not all settings are available with all cycles. | |
| Wrinkle Prevent to add up to 150 minutes of periodic |
| |
|
|
| |
| tumbling to help reduce wrinkling. On models with Wrinkle |
|
|
| Prevent with Steam, a short steam cycle is added after |
|
|
| 60 minutes to help smooth out wrinkles. |
|
|
| Drum Light |
|
|
| Press to turn the drum light on or off. The light will also turn |
|
|
| on when the door is open, and turn off automatically after |
|
|
| about 5 minutes. |
|
|
| Damp Dry Signal |
|
|
| When selected, a signal will sound during the drying |
|
|
| cycle when the load is damp but not completely dry. This |
|
|
| will allow you to take clothes out of the load that do not |
|
|
| need to dry completely. This option is available on Heavy |
|
|
| Duty, Normal, Denim, Bulky, Wrinkle Control, Sheets, Active |
|
|
| Wear, Towels and Delicate cycles. |
| Steam model shown |
| NOTE: The Damp Dry signal defaults to “ON” when using |
| |
|
|
| |
| the Bulky cycle. |
| Airflow |
| Cycle Signal |
| This indicator will show the status of airflow through the dryer |
|
| during Sensor cycles. The Detecting light comes on during | |
| Use this button to turn the signal indicating the end of a |
| |
|
| the sensing phase at the beginning of cycle. The Good light | |
| drying cycle on or off, or to adjust the volume of the signal. |
| |
|
| will come on if no major vent blockage is detected. The Check | |
| NOTE: You may also turn off the tones that sound when a |
| |
|
| Vent light will come on if a blocked vent or low airflow issue is | |
| button is pressed. Press and hold the Cycle Signal button |
| detected. For more information on maintaining good airflow, |
| for about three seconds to turn button sounds on or off. |
| see “Check Your Vent System for Good Airflow”. The Airflow |
| Reduce Static (on some models) |
| sensing feature is available for Sensor cycles only. |
|
| NOTE: If there are other error issues during a cycle, the | |
| Press to add the Reduce Static option to selected Sensor |
| |
| cycles (see Cycle Guide). The dryer will automatically |
| Airflow indicator will not light up. See “Dryer Displaying Code |
| tumble, pause, and introduce a small amount of moisture |
| Message” in “Troubleshooting” section. |
| into the load to help reduce static. This option adds |
| Steam (on some models) |
| approximately 8 minutes to the total cycle time. |
| |
|
| This indicator will light when the Steam function is active. | |
| Steam Boost (on some models) |
| |
|
| NOTE: Steam options are not available on all models or on | |
| Steam Boost adds steam to the end of the Heavy Duty, |
| all cycles. |
| Bulky, Normal, Sheets, Towels, or Denim cycle to help |
| Done |
| smooth wrinkles. |
| |
|
|
| This will indicate that the selected cycle has ended and the |
load may be removed from the dryer. If the Wrinkle Prevent option has been selected, the dryer may continue to tumble the load, even if the DONE indicator is lit.
Check Lint Screen
The Check Lint Screen indicator will light when the drying cycle is complete as a reminder to clean the lint screen.
Wrinkle Prevent
This indicator will light if the Wrinkle Prevent option has been selected and is running. The dryer will continue to periodically tumble the load for up to 150 minutes (depending on model and selected settings) after the cycle has ended.
6
