Manuals / Miller Electric / Power Tools / Welding System

Miller Electric Blue Star 145 manual Description Of Controls Standard Models See Section, To Start

Models: 145 DXR, 145 Blue Star 145

1 54

Download 54 pages 11.08 Kb

Page 25

. Complete Parts List available at www.MillerWelds.com

6-2. Description Of Controls (Standard Models) (See Section 6-1)

1 Engine Switch

Use switch to control ignition circuit. Turn switch to On position when starting engine. Turn switch to Off position to stop engine. En- gine cannot be started with switch in the Off position.

Engine stops if oil level is too low. Engine can- not be restarted until sufficient oil is added.

2 Low Oil Pressure Light

Light goes on and engine stops if engine oil level is too low.

Engine cannot be restarted until sufficient oil is added.

!Stop engine and add oil if light goes on (see Section 5-4).

3Starter Handle

4Choke Control

Use control to change engine air/fuel mix. Move control to far right if starting a cold en-

gine. Move control to far left if starting a warm engine.

To Start:

DOpen fuel valve (see Section 5-4).

DTurn Engine switch to On.

DSet choke.

DPull starter handle. Open choke as en- gine warms.

! If the engine does not start, let engine come to a complete stop before at- tempting restart.

To Stop:

DTurn Engine switch to Off.

.Always close fuel valve after stopping unit. Moving unit with fuel valve open may cause carburetor flooding and make starting difficult.

5 Welding Range Table

Use table to determine correct weld amper- age based on electrode size, type, and mate- rial thickness.

6 Weld Output Control

.Set control at maximum for full generator power output at AC receptacles

Use control to select weld amperage. Control may be adjusted while welding.

To Set Weld Output Control: Use table to determine correct size electrode for weld am- perage. Select electrode type and set control to corresponding amperage range on name- plate. Adjust control to obtain desired weld performance.

EXAMPLE:

Electrode Diameter: 1/8

Electrode Type: E-6013

Current Control Setting: 90 − 120 A

Notes

Work like a Pro!

Pros weld and cut safely. Read the safety rules at the beginning of this manual.

OM-4417 Page 21

Image 25

Miller Electric Blue Star 145, 145 DXR, 145 manual Description Of Controls Standard Models See Section, To Start

Contents

Processes OM-4417210 403FDescription File Engine DriveFrom Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsBuildup of GAS can injure or kill Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionCompressed Air Hazards Engine HazardsHOT Parts can cause burns and injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information Radiation can cause interference− Consignes DE Sécurité − Lire Avant Utilisation Signification des symbolesUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion ’EXPLOSION DE LA Batterie peu LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent pro voquer des blessures ’AIR Comprimé peut provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieRisque D’INCENDIE OU D’EXPLO- Sion DES Organes Mobiles peuvent provoquer des blessures LE Surchauffement peut endom- mager le moteur électriqueLES Fils DE Soudage peuvent provoquer des blessures ’EMPLOI Excessif peutPrincipales normes de sécurité Proposition californienne 65 AvertissementsInformation EMF Symbol Definitions − SpecificationsWeld, Power, And Engine Specifications − DefinitionsDimensions Dimensions, Weights, And Operating AnglesVolt-Ampere Curves Fuel Consumption Duty Cycle Generator Power Curve100% Duty Cycle at 80 Amperes CC/DC Minutes WeldingInstalling Welding Generator − InstallationMovement HazardsEngine Prestart Checks − Standard Model Grounding Generator When Supplying Building SystemsOil Engine Prestart Checks − DX Model Connecting The Battery DX Models OnlySelecting Weld Cable Sizes Connecting To Weld Output Terminals45 m 60 m 70 m 90 m 105 m 120 m 10 − Put terminalsControls Standard Models See Section − Operating the Welding GeneratorStop engine and add oil if light goes on see Section Description Of Controls Standard Models See SectionTo Start Controls DX Models See Section Description Of Controls DX Models See Section − Operating Auxiliary Equipment Generator Power Panel ReceptaclesAC Receptacle RC1 Routine Maintenance − MaintenancePrecleaner Paper Element Servicing Air CleanerStop engine Standard Model ShownStop Engine Close Adjusting Engine Speed Standard Models OnlyValve Tools NeededWeld/Power Speed Adjustment Adjusting Engine Speed DX Models OnlyIdle Speed Adjustment Troubleshooting − TroubleshootingGenerator Power WeldingEngine Recommended Spare Parts − Parts ListRecommended Spare Parts Circuit Diagram For Standard Models − Electrical DiagramsCircuit Diagram for DX Models Selecting Equipment − Generator Power GuidelinesGrounding Generator To Truck Or Trailer Frame How Much Power Does Equipment Require? Grounding When Supplying Building SystemsApproximate Power Requirements For Farm/Home Equipment Approximate Power Requirements For Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentHow Much Power Can Generator Supply? Power Required To Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting AmperageTypical Connections To Supply Standby Power Cord Lengths for 120 Volt Loads Selecting Extension Cord Use Shortest Cord PossibleCurrent Load Watts Amperes Cord Lengths for 240 Volt Loads− Stick Welding Smaw Guidelines Stick Welding ProcedureStriking an Arc − Scratch Start Technique Electrode and Amperage Selection ChartStriking an Arc − Tapping Technique Good Weld Bead Characteristics Poor Weld Bead CharacteristicsPositioning Electrode Holder 10-30 9090 End View of Work AngleElectrode Movement During Welding Conditions That Affect Weld Bead ShapeLap Joint Butt JointsTee Joint 16 in 30 1.6 mm Tack WeldsTroubleshooting − Excessive Spatter Troubleshooting − PorosityWeld Test Possible Causes Corrective ActionsTroubleshooting − Lack Of Penetration Troubleshooting − Incomplete FusionTroubleshooting − Excessive Penetration Troubleshooting − Waviness Of Bead Troubleshooting − Burn-ThroughTroubleshooting − Distortion Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s