Miller Electric Axcess 450 specs

4-7. Rear Panel Receptacles And Supplementary Protectors

			1 115 V 10 A AC Receptacle RC2
			Receptacle		supplies	60	Hz
			single-phase power. Maximum output
	4		from RC2 is limited by supplementary
	2		protector CB1 to 10 amps.
			2	Supplementary Protector CB1
	3	1	3	Supplementary Protector CB2
		1	CB1 protects 115 volt receptacle RC2


			from overload. If CB1 opens, RC2 does
			not work.
			CB2 protects the wirefeed motor from
			overload. If CB2 opens, the wirefeeder
			does not work.
			. Press button to reset breaker. If
				breaker continue to open, contact a
				Factory Authorized Service Agent.
			4 Network Wire Feeder Receptacle
				RC1
			Use receptacle to connect network
			feeder cable to power source (see
			Section 4-6).

Ref. 803 417-A

OM-220 389 Page 17

Image 23

Miller Electric Axcess 450 manual Rear Panel Receptacles And Supplementary Protectors

Contents

File Advanced Manufacturing Systems OM-220 389JProcesses Description From Miller to You Table of Contents − Troubleshooting Decstat1/07 DirectivesStandards Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can kill Flying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosion Moving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injury About Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF Information UNE Décharge Électrique peut entraîner la mort Symboles utilisés LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO LE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-220 389 Keep your head out of the fumes Disconnect input plug or power before working on machine− Definitions Manufacturer’s Warning Label Definitions Weee Label Manufacturer’s Rating Label Symbols And DefinitionsI1max I1eff 17-3/32 in 434 mm 17-3/8 in 441 mm 19-3/32 in 485 mm − InstallationSpecifications Dimensions And Weight Overheating Duty Cycle And OverheatingVolt-Ampere Curves 100% Duty Cycle At 450 Amperes Do not stack units. Beware of tipping Connection DiagramSelecting a Location Rear Panel Receptacles And Supplementary Protectors Incorrect Installation Connecting To Weld Terminals 50/60 Hz Network Wire Feeder Receptacle FunctionsElectrical Service Guide Pin Disconnect Device Input Power Connections Connecting Input PowerWelding Power Source Input Power Connections Selecting Weld Cable Sizes − Recommended Setup Procedures Gun TravelWCL Current Flow Path Welding Circuit Best Using Multiple Welding Power Sources Wire Feeder Drop in the workpiece. The voltage drop Bad Setup Supporting separate voltage feedback to OM-220 389 Better Setup Best Setup PDA Port PC Port OM-220 389 Front Panel Switches− Operation Blowing Out Inside of Unit − MaintenanceRoutine Maintenance Exploding Parts can cause injury − Safety Precautions for ServicingShock Hazard from testing Servicing Hazards California Proposition 65 Warnings Removing Cover and Measuring Input Capacitor Voltage − Troubleshooting Status Diagnosis Process Control Module PC4 Diagnostic LED’sDiagnostic LED’s On Process Control Module PC4 Circuit board is operating normally Network And Module Status LED’s Network Status LED’sModule Status LED’s Red Trouble Remedy Troubleshooting Circuit Diagram For Welding Power Source − Electrical Diagrams 220 420-B 16 − Fig − Parts List Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH -1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Dia Part Support ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact