Directives, Standards, Decstat1/07 | Miller Electric Axcess 450

Declaration of Conformity for

European Community (CE) Products

. This information is provided for units with CE certification (see rating label on unit).

Manufacturer:	European Contact:
Miller Electric Mg. Co.	Mr. Danilo Fedolfi,
1635 W. Spencer St.	Managing Director
Appleton, WI 54914 USA	ITW Welding Products Italy S.r.l.
Phone: (920) 734-9821	Via Privata Iseo 6/E
	20098 San Giuliano
	Milanese, Italy
	Phone: 39(02)98290-1
	Fax: 39(02)98290203

European Contact Signature:

Declares that this product: AxcessE 450

conforms to the following Directives and Standards:

Directives

Low Voltage Directive: 73/23/EEC

Electromagnetic Compatibility Directives: 89/336/EEC, 92/31/EEC, 2004/108/EC

Machinery Directives: 98/37EEC, 91/368/EEC, 92/31/EEC, 133/04, 93/68/EEC

CE Marking Directive: 93/68/EEC

Standards

Arc Welding Equipment − Part 1: Welding Power Sources. IEC 60974-1 Ed. 3, 2005-07

Arc Welding Equipment − Part 10: Electromagnetic Compatibility (EMC) Requirements.

IEC 60974-10 Ed. 1.1, 2004-10

Degrees of Protection Provided By Enclosures (IP Code): IEC 60529 Ed. 2.1, 2001-02

The product technical file is maintained by the responsible Business Unit(s) located at the manufacturing facility.

dec_stat_1/07

Image 5

Miller Electric Axcess 450 manual Directives, Standards, Decstat1/07

Contents

Processes OM-220 389JDescription File Advanced Manufacturing Systems From Miller to You Table of Contents − Troubleshooting Decstat1/07 DirectivesStandards Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burns ARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyes Fire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injury California Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical Devices UNE Décharge Électrique peut entraîner la mort Symboles utilisés LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser LE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-220 389 − Definitions Disconnect input plug or power before working on machineManufacturer’s Warning Label Definitions Keep your head out of the fumes Weee Label I1max Symbols And DefinitionsI1eff Manufacturer’s Rating Label Specifications − InstallationDimensions And Weight 17-3/32 in 434 mm 17-3/8 in 441 mm 19-3/32 in 485 mm Volt-Ampere Curves Duty Cycle And Overheating100% Duty Cycle At 450 Amperes Overheating Do not stack units. Beware of tipping Connection DiagramSelecting a Location Rear Panel Receptacles And Supplementary Protectors Incorrect Installation Connecting To Weld Terminals Electrical Service Guide Network Wire Feeder Receptacle FunctionsPin 50/60 Hz Disconnect Device Input Power Connections Connecting Input PowerWelding Power Source Input Power Connections Selecting Weld Cable Sizes − Recommended Setup Procedures Gun TravelWCL Current Flow Path Welding Circuit Best Using Multiple Welding Power Sources Wire Feeder Drop in the workpiece. The voltage drop Bad Setup Supporting separate voltage feedback to OM-220 389 Better Setup Best Setup PDA Port PC Port OM-220 389 Front Panel Switches− Operation Blowing Out Inside of Unit − MaintenanceRoutine Maintenance Shock Hazard from testing − Safety Precautions for ServicingServicing Hazards Exploding Parts can cause injury California Proposition 65 Warnings Removing Cover and Measuring Input Capacitor Voltage − Troubleshooting Status Diagnosis Process Control Module PC4 Diagnostic LED’sDiagnostic LED’s On Process Control Module PC4 Module Status LED’s Network And Module Status LED’s Network Status LED’sRed Circuit board is operating normally Trouble Remedy Troubleshooting Circuit Diagram For Welding Power Source − Electrical Diagrams 220 420-B 16 − Fig − Parts List Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH -1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Dia Part Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s