Operation, Front Panel Switches | Miller Electric Axcess 450

SECTION 6 − OPERATION

6-1. Front Panel Switches

1Power Switch Turns unit On or Off.

2 Pilot Light

Light indicates status of welding power source, on when unit is on and off when unit is off.

Ref. 803 418-B

3PDA Port

4PC Port

OM-220 389 Page 28

Page 34

Image 34

Miller Electric Axcess 450 manual Operation, Front Panel Switches, PDA Port PC Port OM-220 389

Contents

Description OM-220 389JProcesses File Advanced Manufacturing Systems From Miller to You Table of Contents − Troubleshooting Standards DirectivesDecstat1/07 Page Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burns Welding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyes Falling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injury EMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical Devices Symboles utilisés UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion Risque D’INCENDIE OU D’EXPLO LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesser LES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-220 389 Manufacturer’s Warning Label Definitions Disconnect input plug or power before working on machine− Definitions Keep your head out of the fumes Weee Label I1eff Symbols And DefinitionsI1max Manufacturer’s Rating Label Dimensions And Weight − InstallationSpecifications 17-3/32 in 434 mm 17-3/8 in 441 mm 19-3/32 in 485 mm 100% Duty Cycle At 450 Amperes Duty Cycle And OverheatingVolt-Ampere Curves Overheating Selecting a Location Connection DiagramDo not stack units. Beware of tipping Rear Panel Receptacles And Supplementary Protectors Connecting To Weld Terminals Incorrect Installation Pin Network Wire Feeder Receptacle FunctionsElectrical Service Guide 50/60 Hz Welding Power Source Input Power Connections Connecting Input PowerDisconnect Device Input Power Connections − Recommended Setup Procedures Selecting Weld Cable Sizes Welding Circuit Gun TravelWCL Current Flow Path Best Using Multiple Welding Power Sources Bad Setup Wire Feeder Drop in the workpiece. The voltage drop Better Setup Supporting separate voltage feedback to OM-220 389 Best Setup − Operation Front Panel SwitchesPDA Port PC Port OM-220 389 Routine Maintenance − MaintenanceBlowing Out Inside of Unit Servicing Hazards − Safety Precautions for ServicingShock Hazard from testing Exploding Parts can cause injury California Proposition 65 Warnings − Troubleshooting Removing Cover and Measuring Input Capacitor Voltage Diagnostic LED’s On Process Control Module PC4 Process Control Module PC4 Diagnostic LED’sStatus Diagnosis Red Network And Module Status LED’s Network Status LED’sModule Status LED’s Circuit board is operating normally Troubleshooting Trouble Remedy − Electrical Diagrams Circuit Diagram For Welding Power Source 220 420-B − Parts List 16 − Fig Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH -1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Dia Part Your distributor also gives ServiceSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s