READ INSTRUCTIONS.

D Use only genuine MILLER/Hobart replacement parts.

DPerform engine and air compressor (if applicable) maintenance and service according to this manual and the engine/air compressor (if applicable) manu- als.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio naviga- tion, safety services, computers, and communica- tions equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as microprocessors, computers, and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electro- magnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive electronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

1-6. California Proposition 65 Warnings

YWelding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

YBattery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

For Gasoline Engines:

YEngine exhaust contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

For Diesel Engines:

YDiesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

1-7. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126 (phone: 305-443-9353, website: www.aws.org).

Recommended Safe Practices for the Preparation for Welding and Cut- ting of Containers and Piping, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Mi- ami, FL 33126 (phone: 305-443-9353, website: www.aws.org).

National Electrical Code, NFPA Standard 70, from National Fire Protec- tion Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (phone: 617-770-3000, website: www.nfpa.org and www. sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1735 Jefferson Davis Highway, Suite 1004, Arlington, VA 22202-4102 (phone: 703-412-0900, website: www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Bou-

levard, Rexdale, Ontario, Canada M9W 1R3 (phone: 800-463-6727 or

in Toronto 416-747-4044, website: www.csa-international.org).

Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute, 11 West 42nd Street, New York, NY 10036–8002 (phone: 212-642-4900, website: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, NFPA Standard 51B, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (phone: 617-770-3000, website: www.nfpa.org and www. sparky.org).

OSHA, Occupational Safety and Health Standards for General Indus- try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and Part 1926, Subpart J, from U.S. Government Printing Office, Super- intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there are 10 Regional Offices—phone for Region 5, Chicago, is 312-353-2220, website: www.osha.gov).

1-8. EMF Information

Considerations About Welding And The Effects Of Low Frequency Electric And Magnetic Fields

Welding current, as it flows through welding cables, will cause electro- magnetic fields. There has been and still is some concern about such fields. However, after examining more than 500 studies spanning 17 years of research, a special blue ribbon committee of the National Research Council concluded that: “The body of evidence, in the committee’s judgment, has not demonstrated that exposure to power- frequency electric and magnetic fields is a human-health hazard.” However, studies are still going forth and evidence continues to be examined. Until the final conclusions of the research are reached, you may wish to minimize your exposure to electromagnetic fields when welding or cutting.

To reduce magnetic fields in the workplace, use the following procedures:

1.Keep cables close together by twisting or taping them.

2.Arrange cables to one side and away from the operator.

3.Do not coil or drape cables around your body.

4.Keep welding power source and cables as far away from operator as practical.

5.Connect work clamp to workpiece as close to the weld as possible.

About Pacemakers:

Pacemaker wearers consult your doctor first. If cleared by your doctor, then following the above procedures is recommended.

OM-491 Page 4

Return To Table Of Contents

Page 8
Image 8
Miller Electric Big Blue 502P manual California Proposition 65 Warnings, Principal Safety Standards, EMF Information

Big Blue 602P, Big Blue 502P, Big Blue 402P specifications

Miller Electric is a well-respected name in the welding industry, known for its high-quality portable welders that cater to a wide range of applications. Among their iconic products are the Big Blue 502P, Big Blue 402P, and Big Blue 602P, each offering unique features and capabilities suited to professional welders.

The Miller Big Blue 502P is recognized for its robust construction and high-performance capabilities. Powered by a reliable diesel engine, it provides 500 amps of welding power at a duty cycle of 100%. This model is particularly favored for its versatility, accommodating both stick and TIG welding processes. One of its key technologies is the Auto-Set feature, which automatically adjusts settings for optimal performance based on the material thickness. This welder also boasts a user-friendly interface, complete with easy-to-read digital displays for monitoring essential parameters.

In contrast, the Big Blue 402P offers a slightly lower welding output while maintaining many of the advanced features seen in its larger counterpart. With a maximum output of 400 amps, it is perfectly suited for light to medium-duty applications. The 402P is particularly lightweight for a diesel welder, making it an ideal choice for contractors who need mobility without sacrificing power. It includes the X-Mode technology, which ensures reliable performance in challenging conditions and offers an intuitive control panel for ease of use.

The Big Blue 602P, on the other hand, stands out for its high output and exceptional reliability. With a maximum capacity of 600 amps, this machine is designed for heavy-duty applications, making it perfect for industrial settings. The welder features advanced cooling systems and robust construction, which enhance durability and longevity. One notable characteristic of the 602P is its ability to handle various welding processes, including Stick, TIG, and MIG, making it a versatile tool for skilled welders. Additionally, the Big Blue 602P incorporates advanced inverter technology, resulting in a lighter and more energy-efficient model without compromising power performance.

All three models benefit from Miller's commitment to innovation and user-centric design features. Built to thrive in tough work environments, the Big Blue series is equipped with protective casings and vibration-resistant components. Safety is also a priority, with several built-in features that help protect users during operation.

In summary, the Miller Electric Big Blue 502P, 402P, and 602P each bring unique strengths to the welding market. Their notable features include advanced technologies, robust construction, and versatile applications, ensuring that professionals have the right tool for any welding job. Whether for light-duty tasks or heavy industrial applications, Miller Electric's Big Blue series remains a cornerstone for welders around the globe.