Manuals / Miller Electric / Power Tools / Welding System

Miller Electric Big Blue 500 PT, Big Blue 600 X manual Volt-Ampere Curves For CC Models, Volts

Models: Big Blue 600 X Big Blue 500 PT

1 90

Download 90 pages 33.37 Kb

Page 20

4-3. Volt-Ampere Curves For CC Models

100

		80
	VOLTS	60
	VOLTS	40
	DC	40
	DC
		20
		0

0 100 200 300 400 500 600 DC AMPERES

Ranges

300−Max

185−425

125−320

85−190

55−90

700 800 900

The volt-ampere curve shows the minimum and maximum voltage and amperage output capabilities of the welding generator. Curves of all other settings fall between the curves shown.

Notes

203 412

Work like a Pro!

Pros weld and cut safely. Read the safety rules at the beginning of this manual.

OM-4429 Page 16

Image 20

Miller Electric Big Blue 500 PT, Big Blue 600 X manual Volt-Ampere Curves For CC Models, Volts

Contents

Processes DescriptionFile Engine Drive Visit our website at OM-44292216 138H 2007−05 From Miller to You Table of Contents − Maintenance & Troubleshooting Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burns Fumes and Gases can be hazardous Buildup of GAS can injure or killARC Rays can burn eyes and skin Welding can cause fire or explosion Engine Hazards Compressed Air Hazards Welding Wire can cause injury HOT Parts can cause burns and injuryFire or Explosion hazard Falling Unit can cause injury Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interference Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer Indique des instructions spécifiques DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut affecter l’ouïe ’EXPLOSION DE LA Batterie peu DES Organes Mobiles peuvent pro voquer des blessures Risque D’INCENDIE OU D’EXPLO- Sion LA Chaleur DU Moteur peut pro- voquer un incendie’AIR Comprimé peut provoquer des blessures LE Surchauffement peut endom- mager le moteur électrique DES Organes Mobiles peuvent provoquer des blessuresLES Fils DE Soudage peuvent provoquer des blessures ’EMPLOI Excessif peut Proposition californienne 65 Avertissements Principales normes de sécuritéInformation EMF En ce qui concerne les implants médicaux Std − Definitions− 50 h Std Manufacturer’s Rating Labels CC Models Symbols And Definitions Some symbols are found only on CE products Dimensions, Weights, And Operating Angles − SpecificationsWeld, Power, And Engine Specifications Volt-Ampere Curves For CC Models Volts Stick Mode MIG ModeTIG Mode Volt-Ampere Curves For CC/CV Models 100% Duty Cycle At 400 Amperes Fuel ConsumptionDuty Cycle And Overheating AC Generator Power Curve Optional Three-Phase Generator Curves12 kVA/kW Single-Phase AC Output No Weld Load 20 kVA/kW Three-Phase AC Output No Weld Load − Installation Installing Welding GeneratorLocation/Airflow Clearance Grounding1 Using Lifting Eye Mounting Welding Generator Installing Exhaust Pipe Stop engine and let cool Activating The Dry Charge Battery If Applicable Connecting The Battery Coolant Recovery Tank Engine Prestart ChecksFuel Oil Connecting To Weld Output Terminals Stick and TIG WeldingMIG and Fcaw Welding Stop engine Connecting to Weld Selecting Weld Cable Sizes150 ft 200 ft 250 ft 350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Connecting To Remote 14 Receptacle RC14 On CC/CV Models Socket OM-4429 − Operating Welding Generator − CC Models Front Panel Controls For CC Models See Section Engine Starting Controls To StartEngine Gauges And Meters Weld Controls Example Combination Remote Amperage Control Stick Remote Amperage Control On CC Models OptionalWeld Control/Arc Condition Information Label OM-4429 − Operating Welding Generator − CC/CV Models Front Panel Controls For CC/CV Models See Section Voltage/Amperage Adjust Switch And Remote 14 Receptacle 14 AC/DC Voltmeter Optional Process/Contactor Switch On CC/CV Models Process/Contactor Switch Settings Remote Voltage/Amperage Control On CC/CV Models Optional Example Combination Remote Amperage Control TIG − Operating Auxiliary Equipment Volt And 240 Volt ReceptaclesAt least once a month, run en If a Supplementary Close panel opening if no connections are made to generator Three-Phase Power ConnectionRear Of Panel Supplementary Protector CB2 Supplementary Protector CB3 Optional Generator Power Receptacles240 V 15 a AC South African Receptacle RC1 − Maintenance & Troubleshooting Maintenance Label Routine Maintenance Servicing Air Cleaner To clean air filter Inspecting And Cleaning Optional Spark Arrestor Muffler Checking Generator Brushes To replace primary fuel filter Servicing Fuel And Lubrication SystemsTo change oil and filter Overload Protection Troubleshooting Welding − CC Models Welding − CC/CV Models Engine Standard Generator PowerOptional Three-Phase Generator Power CC/CV Models Only Check engine wiring harness plug connections Gine Control switch S1Factory Authorized Service Agent Engine cranks but does not start Check fuel level Start Your Professional Welding Career Now − Electrical Diagrams Circuit Diagram For CC Welding Generator 223 525-B Circuit Diagram For CC/CV Welding Generator 223 524-B Welding Generator − RUN-IN ProcedureWetstacking From flammables Run-In Procedure Using Load BankKeep exhaust and pipe away Run-In Procedure Using Resistance Grid Specifications section in thisJust generator A/V control so Manual − Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame Electrically Bond Generator Grounding When Supplying Building Systems How Much Power Does Equipment Require?Use ground device as stated in electrical codes Amperes x Volts = Watts Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible 123 116 CV 112 − Parts List114 −7 115 CV 2831 124 88 −6 6059 58 Dia Part Description Quantity Dia Part Description Quantity Mkgs Figures 13-2 111 123 212 Control Box Assembly − CC Models Control Box Assembly − CC Models -1Item Engine Controller Control Box Assembly − CC/CV Models 134 Panel, Front w/Components − CC Models 3634 208278 Panel, Front w/Components − CC/CV Models Panel, Front w/Components − CC/CV Models -1Item CB1 201 Supplementary PROTECTOR, man reset 2P 20 A, 250VAC Hardware is common 32 31 30 053 BEARING, Ball Rdl Sgl Row 1.370 X 2.830 X Main Rectifier Assembly Wiring Harnesses 215207 Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s