Moving Generator

1.Pull folding handle to the upright position until spring pin (A) locks into place.

A

warning

Crush Hazard. Center point lift bracket can crush and cut resulting in bodily injury.

•Keep hands clear of area between bracket and folding handle.

2.Place your foot onto the round bar (B) located under the recoil starter and pull back on the handle.

B

3.Push or pull generator to desired location.

4.Place foot on round bar and gently let generator tip forward to rest on support leg.

5.Pull on spring pin and push handle forward to fold down handle.

Add Engine Oil

• Place generator on a level surface.

NOTE: Verify provided oil bottles are the correct viscosity for current ambient temperature.

•Refer to engine operator’s manual and follow oil recommendations and instructions.

NOTICE

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

•Refer to engine manual for oil information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

NOTE: Check oil often during engine break–in. Refer to engine operator’s manual for recommendations.

Add Fuel

NOTE: Refer to engine operator’s manual and follow fuel recommendations.

warning

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

•Turn generator OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

•Fill fuel tank outdoors.

•DO NOT overfill tank. Allow minimum 3/4” (2 cm) from top of strainer to avoid fuel spillage from cap. Space remaining in tank provides room for fuel expansion and prevents fuel from spilling out vented fuel cap when generator is wheeled.

•If fuel spills, wait until it evaporates before starting engine.

•Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

•DO NOT light a cigarette or smoke.

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded gasoline to fuel tank. Be careful not to overfill. Allow minimum 3/4” (2 cm) (C) from top of strainer to avoid fuel spillage from cap.

C

NOTE: Occasionally clear the fuel strainer of any dirt, rust, or other particulate matter.

3.Install fuel cap and let any spilled fuel evaporate before starting engine.

10

www.milwaukeetool.com

Page 9 Page 11
Page 10
Image 10
Milwaukee 4970-24, 4960-24 manuel dutilisation Moving Generator, Add Engine Oil, Add Fuel, When Adding Fuel
Page 9 Page 11

4960-24, 4970-24 specifications

The Milwaukee 4960-24 and 4970-24 are powerful tools from Milwaukee's renowned lineup, specifically designed to meet the demands of professional tradespeople and DIY enthusiasts alike. These models are standout products in the company's commitment to durability, innovation, and user-friendly features that make them indispensable on the job site and in home improvement projects.

One of the main features of the Milwaukee 4960-24 and 4970-24 is their robust motor design. Both models are equipped with high-performance brushless motors that provide extended runtime and more efficient operation. This advanced motor technology not only ensures durability but also enhances the overall power output, allowing users to tackle even the toughest tasks with confidence.

The Milwaukee 4960-24 focuses on versatility, featuring a compact and lightweight design that makes it easy to maneuver in tight spaces. With an adjustable speed setting, it can accommodate a wide range of applications, from heavy-duty cutting to more delicate precision work. The ergonomically designed handle provides comfort during extended use, reducing fatigue and promoting productivity.

In contrast, the Milwaukee 4970-24 offers an augmented level of performance suited for more demanding applications. With a higher horsepower rating and enhanced torque, this model is ideal for heavy-duty cutting, grinding, and sanding tasks. Its rugged construction is built to withstand the rigors of job site conditions, featuring reinforced housings and robust components designed for long-lasting performance.

Both models boast advanced battery technologies, compatible with Milwaukee's M18 battery system. This compatibility allows users to interchange batteries across a wide selection of Milwaukee tools, improving efficiency and reducing downtime. Additionally, the intelligent battery management system optimizes performance, ensuring that users get the most out of their tools without the frustration of sudden power loss.

Incorporating user-friendly features, such as tool-free blade changes and integrated LED work lights, the Milwaukee 4960-24 and 4970-24 prioritize ease of use. These tools help enhance visibility in dimly lit workspaces and provide quick adjustments, catering to the needs of professionals who require flexibility and efficiency on the job.

In summary, the Milwaukee 4960-24 and 4970-24 are exceptional tools that embody the brand's dedication to quality, performance, and innovation. With their advanced motor technology, robust design, and thoughtful user features, these models exemplify what modern power tools should offer, making them valuable assets for users in various trades and applications.
Top Page Image Contents