(3)Communications exchange condition setting switch setting Set the conditions for data communication with other nodes.
Communications | Switch |
| Setting designation |
| Setting contents | ||||
exchange condition |
|
| |||||||
| setting switch |
|
|
|
|
| |||
|
|
|
|
|
|
|
| Selects the line processing when the | |
|
|
|
|
|
|
| Line processing | TCP ULP time out error occurrence. | |
|
|
|
|
| SW1 |
| selection during | ( 1) |
|
|
|
|
|
|
|
| TCP timeout error | OFF | Close the circuit. |
|
|
|
|
|
|
|
| ON | Do not close the circuit. |
|
|
|
|
|
|
|
| Selects | the type of data code for |
|
|
|
|
|
|
|
| exchanging data with the remote node. | |
|
|
|
|
| SW2 |
| Data code setting | OFF | Conducts exchange in binary |
|
|
|
|
|
| code. | |||
|
|
|
|
|
|
|
|
| |
| OFF ON |
|
|
| ON | Conducts exchange in ASCII | |||
|
|
|
| code. | |||||
| SW1 |
|
|
|
|
|
|
| |
|
|
|
| SW3 to |
| — | Usage not possible (Fixed to OFF) | ||
|
|
| |||||||
| SW2 |
|
| SW6 |
| ||||
|
|
|
| ||||||
| SW3 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| Selects whether to approve or forbid | ||
|
|
|
|
| |||||
| SW4 |
|
|
|
|
|
| ||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| data arriving from the remote node | ||
|
|
|
|
| |||||
| SW5 |
|
|
|
|
| CPU exchange | ||
|
|
|
|
|
| ||||
|
|
| SW7 |
| when a PLC CPU is running. | ||||
| SW6 |
|
|
| timing setting | ||||
|
|
| |||||||
| SW7 |
|
|
|
|
| OFF | Writing prohibited. | |
|
|
|
|
|
|
| |||
|
|
|
|
| |||||
| SW8 |
|
|
|
|
| ON | Writing approved. | |
|
|
|
|
|
| ||||
|
|
|
|
| |||||
|
|
|
|
|
|
|
| Selects | the initial processing starts up |
|
|
|
|
|
|
|
| timing. ( 2) | |
|
|
|
|
|
|
|
|
| Quick start (starts without a |
|
|
|
|
|
|
| Initial timing | OFF | delay |
|
|
|
|
| SW8 |
| network is used for the entire | ||
|
|
|
|
|
|
| |||
|
|
|
|
|
| setting |
| configuration. | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| Normal start (start after a delay |
|
|
|
|
|
|
|
| ON | of 20 |
|
|
|
|
|
|
|
| entire configurations is made | |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| up of multiple networks. |
|
|
|
|
|
|
| (This is set at "OFF" | at the | time of shipping from factory.) |
1 | Set to OFF for normal use. |
|
|
| |||||
| When a TCP ULP time out error (error code: 9059H) occurs due to data transfer from | ||||||||
| remote node while this switch is set to ON, run the close and open operations with the | ||||||||
| sequence program. |
|
|
| |||||
2 | Set to OFF for normal use. |
|
|
| |||||
7
