Mitsubishi Electronics WD-Y577, WD-57734, WD-65733, WD-57733, WD-73734 ChannelView Channel Listings

4. TV Operation and Features 27

Remote Control, continued

Record/Playback Keys

Use any of these methods to enable the recording and playback commands:

•Program the remote control for your DVR, VCR, or DVD player/recorder and set the slide switch to VCR, DVD, CABLE/SAT, or AUDIO as appropriate.

•Y and 734 series TVs: Perform NetCommand IR “learning” for the device.

•Check HDMI devices for compatibility with the TV’s NetCommand for HDMI feature (see below).

23. (Pause): Pauses a VCR, DVR, or DVD. See above for use during TV viewing.

24. (Play): Plays a VCR, DVR, or DVD.

25. (Record): Records with a VCR or DVR.

26. (Stop): Stops play of a VCR, DVR, or DVD.

27. (Reverse): Rewinds a VCR. Reverse scans a DVR or DVD.

28. (Forward): Fast forwards a VCR. Forward scans a DVR or DVD.

Note: To operate other audio/video devices:

•See Appendix D, “Programming the Remote Control.”

•See chapter 6, “NetCommand,” for NetCommand IR “Learning” of device keys.

•For HDMI devices compatible with the TV’s NetCommand for HDMI feature, see below.

NetCommand for HDMI Devices

The TV’s remote may operate some functions of compatible HDMI devices able to receive commands through the HDMI cable. Test your equipment with the TV’s remote to find out which commands are sup- ported. See below for commands that may be avail- able, depending on the individual device.

Press PLAY on the device itself to:

•Turn on the TV if not already on

•Switch to the device (no need to display the Input Selection menu)

•Begin play of the device

VCR, DVD, and DVR functions that may be available:

Record/	Menu	Channel Tuning		Other
Playback	Navigation
		CH	/	Guide
	Enter	Digits 0–9,	—	F1 (content)
			CANCEL
	—	ENTER		MENU
	CANCEL (to cancel)

Low-Battery Indicator

If you press a key and the POWER key blinks five times, replace the remote control’s batteries.

Resetting the Remote Control

If the slide switch is set to TV and the TV does not respond properly, reset the remote control.

1.Press and hold POWER for several seconds until the button blinks twice and goes off.

2.Release the POWER button.

3.Press keys 0 0 9 3 5 and the POWER button will blink twice when you finish entering the code. While entering the code, pause for a moment between each key press to ensure it is recognized.

Care of the Remote Control

•Use only alkaline batteries.

•Be within 20 feet of the equipment.

•Do not press two or more buttons at the same time unless instructed to do so.

•Do not allow unit to get wet or become heated.

•Avoid dropping on hard surfaces.

•Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth.

•Do not mix old and new batteries.

ChannelView™ Channel Listings

ChannelView shows memorized channels on ANT 1 and ANT 2. It displays channel names and program information as sent by broadcasters or your local cable service provider and may be incomplete. No program information is displayed for analog channels. An analog channel name is displayed only if you assigned a name in the Setup > Edit menu.

To receive ChannelView updates, set the Energy Mode to Fast Power On and leave the TV powered off for a while each day.

Using ChannelView

Feature	Press Key
See ChannelView listings	Press GUIDE.
from ANT 1 or ANT 2.
Close ChannelView	Press GUIDE or EXIT.
Scan channels one by one.	Press and hold or .
Scan channels quickly.	Press and hold PAGE  / .
Jump to listings for a spe-	1.	Enter the channel
cific channel.		number (see numbers
		in upper left.
	2.	Press ENTER.
See more of the program	Press INFO.
description.
Move navigation to the	Press .
program guide.
Move navigation to the	Press .
channel guide.
Tune to the highlighted	Press ENTER.
channel.