26Chapter 2. Connecting
Antenna with a Single Lead
Figure 5
A. For an antenna with flat twin leads
A
Antennas with Separate UHF and VHF Leads
Figure 6
A UHF/VHF combiner is required. This is not included with the TV, but is available at most electronics stores.
A1. For an antenna with flat twin leads, connect the 300- ohm twin leads to the
A2. Push the
B.For cable or antenna with coaxial lead
Connect the coaxial lead directly to ANT 1 on the TV back panel.
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
0IN 0IN
'MBU5XJO $PBYJBM
$BCMF
#
DT V
C BLE/
VHF
UHF
" |
|
ANT 1 | |
|
|
" 0QUJPOBM0IN UP0IN
.BUDIJOH5SBOTGPSNFS
Figure 5. Connecting a Single Antenna
1.Connect the UHF and VHF antenna leads to the UHF/ VHF combiner.
2.Push the combiner onto ANT 1 on the TV back panel.
7)'"OUFOOB 6)'"OUFOOB $IBOOFMT $IBOOFMT
57#BDL1BOFM
|
| COMPONENT |
INPUT | YPbPr (480i/480p/720p/1080i) | |
| 1 | 2 |
| 1 | 2 |
| INPUT | OUTPUT | |
'MBU |
| Y | 1 | |||
| Pb | 2 |
|
| ||
|
|
|
| DVI | AUDIO | RECORD |
5XJO |
| Analog Audio | OUTPUT | OUTPUT | ||
|
|
|
|
| VIDEO | |
AUDIO- | AUDIO- |
|
|
|
| |
| VIDEO | Pr |
|
|
| AUDIO- |
|
|
|
|
|
| LEFT/ |
'MBU |
|
|
|
|
| (MONO) |
AUDIO- | AUDIO- |
|
|
|
| |
| LEFT/ | LEFT/ |
|
|
| AUDIO- |
| (MONO) | (MONO) |
|
|
| |
|
|
|
|
| RIGHT | |
RIGHT | RIGHT |
|
|
|
| |
|
| 1 |
| 2 |
| |
5XJO |
|
| MONITORLINK™/HDMI |
| ||
|
|
| VIDEO 480i/480p/720p/1080i |
| ||
|
|
| AUDIO PCM LINEAR |
| ||
|
|
|
|
|
| SERVICE |
|
|
|
|
|
| PORT |
&YUFSOBM
"OUFOOB
PS$BCMF
DTV/CABLE/
VHF/UHF
|
| DIGIT L |
|
| AUDIO |
| ANT 1 | OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0INUP |
|
|
0IN |
|
|
$PNCJOFS | DTV/CABLE/ | |
6)' | VHF/UHF | |
7)' |
|
|
ANT 1
#BDL 4JEF 7JFX 7JFX
5P"/5
Figure 6. Connecting separate UHF and VHF Antennas
Mitsubishi strongly recommends you avoid using antennas with flat twin leads. Flat twin lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable.
Downloaded from www.Manualslib.com manuals search engine
