Mitsubishi Electronics WS-65815 manual Back Panel, IEEE-1394 Input/Output, Digital Audio Output

Back Panel

ANT-2	ANT-1
AUX	MAIN
IEEE1394	DIGITAL
	AUDIO
INPUT/OUTPUT	CableCARDTM SLOT
– (DTV/CABLE /VHF/UHF) –

1. 2. 3. 4.

10.9.

	INPUT	MONITOR OUTPUT
1	2	AUDIO/VIDEO 1 AUDIO 2
		S-VIDEO
		VIDEO
		AUDIO-
		LEFT/
		(MONO)
		IR EMITTER
		NetCommand R
		AUDIO-
		RIGHT

	COMPONENT
YPbPr (480i/480p/1080i)
1	2	SERVICE WARNING

	Y	CAUTION: TO			MEASURE SECOND
		ANODE VOLTAGE USE A HIGH VOLTAGE
		METER CONNECTED FROM ANODE LEAD
		TO CHASSIS ONLY. DISCHARGE HIGH
	Pb	VOLTAGE TO CHASSIS ONLY, NOT TO
		EXTERNAL GROUND.
		WARNING: HANDLE WITH CARE. HIGH
		VACUUM PICTURE TUBE IS DANGEROUS
	Pr	TO HANDLE.		REFER		SERVICING TO
		QUALIFIE D		SE RV ICE		PE RSONNEL.
	AUDIO-	REPLACE WITH A TUBE OF THE SAME
DVI		TYPE NUMBER FOR CONTINUED SAFETY.
Analog Audio	LEFT/	X-RAY PRECAUTION: THIS PRODUCT
	(MONO)
Digital Video		I NCLUD E S CR I T I CA L				ME CHA NI CA L
Digital Audio		AND ELECTRICAL PARTS WHICH ARE
	AUDIO-	ESSENTIAL FOR X-RADIATION						SAFETY.
		FOR CONTINUE D			SAFE TY		RE PLACE
	RIGHT
		CRITICAL COMPONE NTS					INDICATE D
		IN THE SERVICE MANUAL ONLY WITH
		EXACT	REPLACEMENT			PARTS		GIVEN
		IN THE	PARTS	LIST.	REFER		TO	SERVICE
		MANUAL FOR OPERATING HIGH VOLTAGE AT
		MINIMUM BRIGHTNESS,				MEASUREMENT
		PROCEDURES		AND	PROPER SERVICE
		ADJUSTMENTS.

5. 6. 7.

8.

1. IEEE-1394 Input/Output

Use these jacks to connect the TV to external IEEE 1394 digital products by means of a single cable. There are two jacks on the back panel for all models and one on the front panel. IEEE 1394 connections provide a high degree of flexibility when connecting your NetCommand® controlled system. Detailed information regarding IEEE 1394 connection requirements are in Chapter 2.

2.Antenna (ANT-1 MAIN, ANT-2 AUX)

ANT-1 MAIN and ANT-2 AUX can each receive both digital/analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable channels.

Your primary viewing signal source should be connected to ANT-1 MAIN. ANT-1 MAIN must be used to view premium subscription cable TV service authorized by the CableCARD™ access card. The CableCARD access card is provided by your local cable company. ANT-2 AUX can continue to receive over-the-air or non-scrambled cable signals.

3. Digital Audio Output

This output will automatically send Dolby® Digital audio from digital channels, IEEE 1394 devices and HDMI™ (not DVI) signals to a digital Audio/Video receiver. Connect this output to the A/V receiver’s coaxial digital audio input. This output will automatically turn off when viewing an analog channel or device. Use Monitor Ouput Audio 2 to send analog signals to your A/V receiver.

Some digital cable channels send MPEG-1 digital audio instead of Dolby Digital, however, not all A/V receivers can decode MPEG-1 digital audio. This can cause the A/V receivers to produce a loud noise that can damage speakers. For this reason, the TV will automatically turn off the digital audio output when tuned to a channel or device that has MPEG-1 digital audio and send it to the A/V receiver as analog left and right audio from Monitor Output. You can enable the digital output to include MPEG-1 digital audio if your A/V receiver is capable of decoding it. See Edit NetCommand in Chapter 3 for details.

10