Connecting the IR Emitter NetCommand®

IR Emitter NetCommand®

Figure 13

A quadruple IR Emitter cable is included with the TV.

The emitters connected to these jacks are used by the NetCommand system to control other devices such as VCR, DVD players, Cable boxes and Satellite receivers.

1.Connect the plug end of the supplied quadruple IR Emitter Cable to one of the IR Output NetCommand jacks on the TV back panel.

2.Run the cable for each of the emitter ends under, along side or over the top of each device to be controlled to the area of the front where the remote control sensor is located.

3.Place the emitter end in front of the remote control sensor of the device to be controlled. The emitter bulb should face the remote control sensor. This bulb emits infrared light in a cone shaped pattern. The bulb needs to be placed far enough from the remote control sensor to allow the cone pattern to include the sensor.

The remote control sensor is usually behind the plastic window of the front display panel. It is sometimes visible when you look through the display plastic using a flashlight and is normally a round or square cutout behind the plastic. If you cannot see the sensor and the device’s Owner’s Guide does not specify the

location, you can find it by using the device’s remote control. Hold the remote about 1/2 inch from the front of the device. Starting from one end of the display window plastic, press the POWER button.

If the device does not respond, move the remote control 1 inch toward the center and try again. Repeat this until the device responds. Note this location then start over from the other end of the display window plastic, repeating until the device responds again. The remote control sensor will be somewhere between these two positions. This is usually enough accuracy for the placement of the IR emitters.

4.With some devices, the emitter will work better facing downward from the top of the device. Some experimentation may be needed.

5.The emitter end being used can be secured in place using double stick tape.

6.If you are not going to be using all emitter ends, place the unused ends behind the devices, on a shelf or in an out-of-the-way location so that they cannot send signals to the remote control sensors.

TV back panel

 

 

(section detail)

 

 

 

1.

6.

 

 

IR EMITTER

 

 

NetCommand

 

shelf

 

 

4.

 

 

Other A/V device

 

 

 

 

2.

 

 

Other A/V device

 

 

3.

A/V Receiver

 

 

3.

 

 

IMPORTANT

If a single emitter end can be placed in a position that will operate more than one device, do not use a separate emitter end for the additional device. A single device receiving remote control signals from too many emitters or remote controls may not respond at all.

Figure 13. Connecting IR Emitter NetCommand

22

Page 21 Page 23
Page 22
Image 22
Mitsubishi Electronics WS-65815, WS-55815 manual Connecting the IR Emitter NetCommand
Page 21 Page 23

WS-55815, WS-65815 specifications

The Mitsubishi Electronics WS-65815 and WS-55815 are high-quality rear-projection televisions that gained popularity in the early 2000s for their impressive display performance and advanced features. These models were designed to provide an immersive viewing experience, highlighting Mitsubishi's commitment to innovation in the home entertainment market.

One of the standout features of the WS-65815 and WS-55815 is their large screen sizes. The WS-65815 offers a massive 65-inch display, while the WS-55815 comes in at 55 inches. Both models utilize a DLP (Digital Light Processing) technology that delivers exceptional picture quality with vibrant colors and sharp details. DLP technology also contributes to deeper blacks and a higher contrast ratio, enhancing the overall visual experience.

Mitsubishi incorporated a 16:9 aspect ratio in both models, which is ideal for watching widescreen content, such as movies and sports events. The advanced color wheel in these televisions enhances the saturation and chromatic accuracy of the images displayed. Additionally, both models support 1080p resolution, making them compatible with high-definition broadcasts and Blu-ray Disc viewing, ensuring users can enjoy stunning picture clarity.

Another key characteristic of the WS-65815 and WS-55815 is their integrated video processing technology. The units feature a built-in 3D Y/C digital comb filter that significantly improves image quality by reducing artifacts and enhancing detail resolution. The televisions also offer multiple input options, including HDMI and component video, allowing users to connect various devices such as gaming consoles, cable boxes, and DVD players seamlessly.

The design of both models is characterized by a sleek cabinet finish, which allows them to blend seamlessly into modern home décor. Furthermore, the televisions are equipped with a user-friendly remote control with programmable features, enabling easy navigation through channels, inputs, and settings.

In summary, the Mitsubishi Electronics WS-65815 and WS-55815 rear-projection televisions stood out for their impressive screen size, advanced DLP technology, and rich, immersive picture quality. These models remain noteworthy examples of Mitsubishi’s innovation in television technology, making them desirable among enthusiasts even in today’s evolving market.
Top Page Image Contents