Mitsubishi Electronics WS-55815, WS-65815 Hdmi Device, External DTV Receiver with Component Video

Connecting an HDMI Device or

External DTV Receiver with Component Video

HDMI Device

Figure 11

An HDMI-to-HDMI cable is required. This is not included with the TV. It may be available at your local electronics retailer

Connect an HDMI cable from the TV back panel to the HDMI device output. HDMI devices provide video and audio through this cable, so no other connection is required.

2 on the TV back panel, matching the correct connections:

DTV Receiver to TV Back panel

• Y to Y
•	Pr to Pr
•	Pb to Pb

TV back panel

DVI

Analog Audio

Digital Video

Digital Audio

ANT-2	ANT-1
AUX	MAIN
	DIGITAL
INPUT/OUTPUT	AUDIO
	CableCARD SLOT

(DTV/CABLE /VHF/UHF)

	INPUT	MONITOR OUTPUT
1	2	AUDIO/VIDEO 1 AUDIO 2
			AUDIO-
			LEFT/
			(MONO)	IR EMITTER
			AUDIO-	NetCommand
			RIGHT
		COMPONENT
	YPbPr (480i/480p/1080i)
	1	2	SERVICE WARNING
		Y	CAUTION: TO			MEASURE SECOND
			ANODE VOLTAGE USE A HIGH VOLTAGE
			METER CONNECTED FROM ANODE LEAD
			TO CHASSIS ONLY. DISCHARGE HIGH
		Pb	VOLTAGE TO CHASSIS ONLY, NOT TO
			EXTERNAL GROUND.
			WARNING: HANDLE WITH CARE. HIGH
			VACUUM PICTURE TUBE IS DANGEROUS
		Pr	TO HANDLE.		REFER		SERVICING TO
			QUALIFIE D		SE RV ICE		PE RSONNEL.
		AUDIO-	REPLACE WITH A TUBE OF THE SAME
			TYPE NUMBER FOR CONTINUED SAFETY.
		LEFT/	X-RAY PRECAUTION: THIS PRODUCT
		(MONO)
			I NCLUD E S CR I T I CA L				ME CHA NI CA L
			AND ELECTRICAL PARTS WHICH ARE
		AUDIO-	ESSENTIAL FOR X-RADIATION SAFETY.
		RIGHT	FOR CONTINUE D			SAFE TY		RE PLACE
			CRITICAL COMPONE NTS					INDICATE D
			IN THE SERVICE MANUAL ONLY WITH
			EXACT	REPLACEMENT			PARTS		GIVEN
			IN THE	PARTS	LIST.	REFER		TO	SERVICE
			MANUAL FOR OPERATING HIGH VOLTAGE AT
			MINIMUM BRIGHTNESS,				MEASUREMENT
			PROCEDURES		AND	PROPER SERVICE
			ADJUSTMENTS.

4. Connect the L (left) and R (right) audio cables from

the DTV receiver to Component 1 or 2 AUDIO LEFT

and AUDIO RIGHT on the TV back panel. If you

connected the YPrPb outputs to Component 1, also

use Component 1 to connect the audio cable. The

red cable connects to the R (right) channel and the

white cable connects to the L (left) channel.

HD-6000 Receiver

Note: To utilize the benefits of a digital A/V receiver, connect your DTV receiver’s digital audio out to a digital input on your digital A/V receiver.

Figure 11. Connecting an HDMI Device

External DTV Receiver with Component Video

2.
Incoming
Antenna
or Cable
2.	DVI
	Analog Audio
	Digital Video
	Digital Audio
ANT-2	ANT-1
AUX	MAIN
	DIGITAL
INPUT/OUTPUT	AUDIO
	CableCARD SLOT
(DTV/CABLE /VHF/UHF)

DTV Receiver (with YPrPb connections)

	INPUT	MONITOR OUTPUT
1	2	AUDIO/VIDEO 1 AUDIO 2
			S-VIDEO
			VIDEO
			AUDIO-
			LEFT/
			(MONO)		IR EMITTER
			AUDIO-		NetCommand
			RIGHT
		COMPONENT
	YPbPr (480i/480p/1080i)
	1	2		SERVICE WARNING
		Y	CAUTION: TO				MEASURE SECOND
			ANODE VOLTAGE USE A HIGH VOLTAGE
			METER CONNECTED FROM ANODE LEAD
			TO CHASSIS ONLY. DISCHARGE HIGH
		Pb	VOLTAGE TO CHASSIS ONLY, NOT TO
			EXTERNAL GROUND.
			WARNING: HANDLE WITH CARE. HIGH
			VACUUM PICTURE TUBE IS DANGEROUS
		Pr	TO	HANDLE.		REFER		SERVICING TO
			QUALIFIE D			SE RV ICE		PE RSONNE L.
		AUDIO-	REPLACE WhiteITH A TUBE OF THE SAME
			TYPE NUMBER FOR CONTINUED SAFETY.
		LEFT/	X-RAY PRECAUTION: THIS PRODUCT
		(MONO)
			I NC L U D E S C R I T I C A L ME C HA N I C A L
			AND ELECTRICAL PARTS WHICH ARE
		AUDIO-	ESSENTIAL FOR X-RADIATION SAFETY.
		RIGHT	FOR	CONTINUE D			SAFE TY RE PLACE
			CRITICAL COMPONERed NT S INDICAT E D
			IN THE SERVICE MANUAL ONLY WITH
			EXACT		REPLACEMENT			PARTS	GIVEN
			IN THE		PARTS	LIST.	REFER TO		SERVICE
			MANUAL FOR OPERATING HIGH VOLTAGE AT
			MINIMUM BRIGHTNESS,					MEASUREMENT
			PROCEDURES			AND	PROPER SERVICE
			ADJUSTMENTS.

3.

4.

Figure 12

A coaxial splitter, RCA video cables and audio cables are required. These are not included with the TV.

1.Connect the outside antenna, cable or satellite to ANT or SATELLITE IN on the DTV receiver (see your DTV receiver’s owner’s guide for instructions and cable compatibility).

2.Connect the incoming terrestrial antenna or cable (not satellite) to ANT-1 on the TV back panel

(a coaxial splitter, available at most electronic supply stores, may be required to complete this installation).

3.Connect RCA-type cables from the YPrPb outputs on the DTV receiver to either Component 1 or

3.						4. White			CAUTION
									RISK OF ELECTRICAL SHOCK
		Y	AUDIO	AUDIO	VCR				DO NOT OPEN
			L	L
					CONTROL			OUT TO TV
		Pr						CH 3
			R	R			Red	CH 4
						DIGITAL
	RF					AUDIO OUT
		Pb
PHONE JACK	REMOTE		VIDEO	VIDEO
					S-VIDEO			IN FROM ANT	SATELLITE IN
									or
								1.	to antenna,

cable or satellite

1.

Figure 12. Connecting an External DTV Receiver with Component Video Connections

IMPORTANT

See Appendix B for component video signal compatibility information.

For digital audio connections, see your DTV Receiver and A/V Receiver Owner’s Guides.

21