Mitsubishi Electronics XD250U-ST Overview

EN-6

Overview

1FOCUS ring

2 Control panel

3 Air inlet grille

4 Remote control sensor (Front)

5 Air outlet grille

6 Terminal board

7 Speaker

8 Adjustment feet

9 Lock bar

10 Lamp cover

Caution:

Do not replace the lamp immediately after using the pro-

jector because the lamp would be extremely hot and it

may cause burns.

Control panel

1 Power button

2 SOURCE button

Each press of this button enables the input source to

switch in the following order: COMPUTER 1, COM-

PUTER 2, HDMI, VIDEO, and S-VIDEO.

3 STATUS indicator

4 POWER indicator

Terminal board

1Power jack

2 COMPUTER IN terminal (1, 2) (Mini D-SUB 15-pin)

3 MONITOR OUT terminal (Mini D-SUB 15-pin)

4 Remote control sensor (Rear)

5 AUDIO IN-1 terminal (Mini jack)

6 AUDIO IN-2 terminal (Mini jack)

7 AUDIO OUT terminal (Mini jack)

8 S-VIDEO terminal

9 VIDEO terminal

10 SERIAL (RS-232C) terminal (Mini DIN)

11 Kensington Lock

12 LAN terminal (RJ-45)

13 AUDIO IN-3 terminals (L/R)

14 HDMI terminal (HDMI 19-pin)

Kensington Lock

This projector has a Kensington Security Standard con-

nector for use with Kensington MicroSaver Security Sys-

tem.

Refer to the information that came with the Kensington

System for instructions on how to use it to secure the pro-

jector. Please contact Kensington Technology Group

below.

Kensington Technology Group

2855 Campus Drive

San Mateo, CA 94403, U.S.A.

Phone: +1- (650)572-2700 Fax: +1- (650)572-9675

10

874

12 3

9

6

5

3214

75138 214 3 1012 4

61

9 11

Contents

Main WARNING DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION When using the projector in Europe: COMPLIANCE NOTICE CAUTION CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, Contents Important safeguards WARNING: Overview Control panel 9 11 Terminal board Kensington Lock Overview (continued) Bottom side Remote control Remote control Battery installation Reception angle (vertical) Operation range (of the remote control) Reception angle (horizontal) Reception angle (vertical), ceiling mount Installation Layout of the projector Front projection Front projection, ceiling mounting Ceiling Mount Installation Basic connections Projector + AV device Projector + DVD player or HDTV decoder Basic connections (continued) Connection (for video equipment having an HDMI terminal) Basic connections (continued) Projector + Computer For computer with Mini D-SUB For analog connection: For monitor connection: Preparation Preparation for projection Warning: Caution: Adjustment of the projection angle Basic operation Power-on Important: When fine streaks are seen on projected images 4 Basic operation (continued) Power-of f 1. 2. 3. Basic operation (continued) Wall Screen When connecting to a laptop computer: Menu operation QUICK MENU QUICK MENU QUICK MENU Basic operation QUICK MENU Menu Options Set the following options provided in the respective menus. 2.INFORMATION menu 1.QUICK MENU DETAIL MENU * Menus are not displayed when no signal is supplied to the projector. cannot be selected when the Input Source is HDMI input. LOW CONTRAST Basic operation Important: IMAGE ADVANCED menu INSTALLATION Menu Options 2.INSTALLATION menu INSTALLATION ADVANCED menu 3.FEATURE menu You can select CINEMA MODE only when the input signal is a TV60, TV50, 480i, or 576i video signal. 4.SINGAL menu SIGNAL USER menu 5.NETWORK menu You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is input. NETWORK IP CONFIG menu 6.INFORMATION menu Image adjustment Adjusting projected images To adjust the brightness (CONTRAST and BRIGHT- NESS): CONTRAST BRIGHTNESS Image adjustment (continued) BrilliantColor RGB-COLOR RGB-TINT How to adjust the image supplied from the computer using the menu: Network settings Setting Projector Name Network Password Settings IP Settings Network settings (continued) Setting or Clearing DHCP IP Address Settings Subnet Mask Settings Default Gateway Settings Network settings (continued) How to Use Network Function Glossary Advanced features Displaying a user-defined image during startup or mut- ing Procedure Freeze To stop the motion in the image temporarily (or to dis- play a still image): Advanced features (continued) To cancel the password function: Magnify To use the MAGNIFY mode: Advanced features (continued) Supervising and controlling by computer Major functions Connection Using the User Manual Lamp replacement Lamp replacement (continued) Reset of the lamp operation time Interval of lamp replacement Caution: Troubleshooting Unplug the power cord from the wall outlet and contact your dealer. No image appears on the screen. J Troubleshooting (continued) Images are not displayed correctly. Troubleshooting (continued) Others If the following problem occurs after the lamp is replaced, check the following first. Maintenance Warning: Indicators Abnormal condition Normal condition Specifications Specifications (continued) Connectors Dimensional drawings (unit : mm) Whats included in the box Replacement part Specifications (continued) Specification of RGB signals in each computer mode of the projector Mitsubishi Projector Warranty, Sales Support and Service Information MITSUBISHI ELECTRIC CORPORATION Ver.1 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan