Mitsubishi Electronics XD250U-ST user manual Basic operation

Basic operation (continued)

Power-off

Use the following procedure to turn off the projector.

The lamp may deteriorate if the projector is powered off and on repeatedly within 30 minutes after the lamp is lighted.

1.Press the POWER button on the control panel or the STANDBY button on the remote control.

•The message "POWER OFF? YES : PRESS AGAIN" appears on the screen.

•To cancel, press any button except the POWER button. (Some buttons on the remote control don’t function for can- cel.)

2.Press the POWER button on the control panel or the STANDBY button on the remote control within 10 seconds again.

•The lamp will go out and the STATUS indicator will start blinking.

•Though the lamp goes out at this second press of the POWER button (or STANDBY button), the air outlet fans con- tinue operating for one minute to cool down the lamp. The STATUS indicator will stop blinking.

•After stopping the air outlet fans, if the temperature inside the set is still high, the temperature sensor detects it and then the air outlet fans may start again.

3.Unplug the power cord.

•The POWER indicator will go out.

•If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 min- utes with the power off. To light the lamp again, press the POWER button (or ON button). If the lamp doesn’t light up immediately, repeat pressing the POWER button (or ON but- ton) two or three times. If it should still fail to light up, replace the lamp.

Notice:

•When storing the projector in the carrying case, the lens should face up.

Instant Shut Down

You can turn off this projector just by unplugging the power cord with- out pressing the POWER button.

•Don't shut down the projector while the STATUS indicator is blink- ing after the lamp lights up because the lamp's life may be short- ened.

•Don't turn the projector back on right after shutting it down because the lamp's life may be shortened. (Wait about 10 minutes before turning the projector back on.)

•Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without closing the menu, the setting data of the menu may not be saved.

•If you shut down the projector while controlling the projector using the network function, the application software such as Projector- View may fail. For details, see "User Manual of LAN Control Utility" contained in the CD-ROM.

AUTO POSITION button

When the image isn’t projected in the right position with COMPUTER selected as the input source, follow the procedure below.

1.Project a bright image such as the "Recycle Bin" window on the full screen.

2.If the screen saver is running, turn it off.

3.Press the AUTO POSITION button.

•If the image is still not in the right position, adjust the image position using the SIGNAL menu. See page 23.

Volume from the speaker

Press the VOLUME S or T button to change the volume from the speaker.

The volume control bar will appear on the screen.

VOLUME 10

•The volume control bar will disappear about 10 seconds after the VOLUME button is released.

•The VOLUME buttons don’t function while the menu selection bar or the menu is being displayed.

•When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminal, the output from the speaker may be distorted.

AV mute

The video and audio signals are temporarily muted when the AV MUTE button is pressed. To cancel muting, press the AV MUTE button again.

Setting the aspect ratio

You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal.

How to change the settings:

With the remote control:

1.Press the ASPECT button.

•Every time the ASPECT button is pressed, the aspect mode changes from NORMAL to 16:9, to FULL, and back to NOR- MAL.

With the FEATURE menu:

(See page 22 for menu setting.)

1.Display the FEATURE menu.

2.Select ASPECT by pressing the S or T button.

3.Select your desired aspect ratio by pressing the W or X button. When 16:9 is selected.

4.Press the ENTER button.

5.Select your desired position (CENTER, UPPER or LOWER) by pressing the W or X button.

To cancel the menu:

6.Press the MENU button.

opt.

FEATURE

ASPECTNORMAL

Important:

•When a 16:9 image is kept displayed for a long time before dis- playing 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen. Consult your dealer in this case.

Caution:

•After using the projector, wait one minute for the air outlet fans to stop in normal use. Then unplug the power cord from the wall out- let.

•The lamp can’t be lit again for one minute after turned off for safety purpose. It will take another one minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button.

•The air outlet fans rotate faster as the temperature around the pro- jector rises.

•When the temperature around the projector rises high, the sign "TEMPERATURE!!" blinks red on the screen. If the temperature stays high, the lamp will go out automatically.

Important:

•Do not display a still picture for a long time because the afterim- ages may persist on the screen.

ENGLISH

EN-15