Motorola 3460 Fast'R Plus C-7

3460 Fast’R

C-7

+FCS= Sets negotiated T.30 parameters for session.

VR, BR,

WD, LN,

DF, EC,

BF, ST

See Table2-8

+FLI= aDefines local ID string a for TSI/CSI signals. Sent to

remote modem.

+FPI= aDefines local polling ID string a for CIG signals. Sent to

remote modem.

+FNR= r, t, i, n Controls the reporting of messages generated during

T.30 Phase B negotiations.

r - RX parameter messages

t - TX parameter messages

i - ID string messages

n - non-standard frame messages

For each sub-parameter, the options are:

0Prevents reporting of messages

1 Reports messages

+FPS= nContains value representing T.30 post page response;

includes page quality and end-of-page status

1See Table 2-7

2 - 4 See Table 2-7

Table 2-2.

Fax Class 2.0 AT Command Set

(continued)

Command Option Description

The characters AT or at precede all commands except: +++, #####, and A/

Parameters and options shown shaded gray vary by country. For your country’s options,

refer to the 3460 Fast’R Reference Guide (T0022).

Default (pre-set) options are underlined.

Contents

Main Notices Page Page Contents Page About This Guide Introduction Page Product Company/Organization Page Chapter 1 Introduction 3460 FastR Overview Network Management Support 1-2 1-3 Page Chapter 2 Access Security Functions In This Chapter Enabling Password Verification by a Local Modem Step Stage Step Stage Page Command Factory Default Option Description Appendix A Specifications In This Appendix Physical Characteristics Operating Modes Fax Environmental Limits Product Safety Regulatory Marking Condition Modem Card AccessWay Stand-Alone Condition Modem Card AccessWay Stand- Alone Electromagnetic Compatibility Fax Branding AccessWay Enclosure Power Supply and Power Requirements Figure A-1. AccessWay Backplane Connectors AccessWay Enclosure Connectors and Interfaces A-7 Modems That Support Two-Wire Leased or Dial Connections Modems That Support Two- or Four-Wire Leased or Dial Connections LINE A Connectors LINE B Connectors Computer Interface V.24 Signal Number Pin Circuit Function RJ11 Interface Pinouts Pin Function Page Step Stage Vanguard 3460 V.34 Daughtercard Connectors and Interfaces Pin Signal Stand-Alone Modem Interfaces and Connectors Computer Interface Pin Circuit Function Page Network Management Interface Pinouts Power Interface Step Stage A-17 Panel Indicators and Switches Front Panel Interface Indicator Description Front-Panel User Interface Figure A-2. 3460 FastR Plus Modem Front Panel Interface Front Panel Interface (continued) Indicator Description Compatibility Button Function Page Appendix B Country-Specific Information B-2 Australia, New Zealand B-3 Austria B-4 Belgium B-5 Canada B-6 Denmark, Netherlands, Luxembourg B-7 Finland 3460 FastR B-8 Option Available France S-Register Command Cross-Reference Register Parameter Command Description B-9 Germany B-10 India B-11 Italy B-12 Japan B-13 Malaysia B-14 Norway B-15 Portugal B-16 Singapore B-17 South Africa B-18 Spain B-19 Switzerland B-20 Universal/International B-21 Universal/International - CTR21 3460 FastR B-22 Universal/International - CTR15, CTR17, CTR21 B-23 Universal/International - K.21 B-24 Universal/International - K.21- Czech Republic B-25 U. S. A. Page Appendix C Attention (AT) Commands for Fax In This Appendix AT Command Set Table 2-1. Fax Class 1 AT Command Set C-2 Action Commands C-3 Configuration Commands C-4 C-5 Capabilities Identification and Control Commands C-6 Action Commands Configuration Commands C-7 C-8 C-9 Page C-11 Result Messages and Codes Table 2-3. Result Messages and Codes Text Form Numeric C-12 C-13 C-14 C-15 Table 2-4. Disconnect Reasons Text Form Numeric Code Description Code Description C-16 Table 2-5. +FHS Command Responses: Hang-Up Status Codes Value Description Table 2-4. Disconnect Reasons (continued) Code Description Code Description C-17 Table 2-5. +FHS Command Responses: Hang-Up Status Codes (continued) Value Description Page C-19 Table 2-8. Frame Sub-Parameters Label Function Value Description Page Index