Programming Scanning Modes | Motorola ENHANCED CELLULAR TELEPHONE

Programming Scanning Modes

Overview

The characteristics that determine the way your phone operates in the Cellular System are determined by the Scanning Mode programmed for your phone.

Reviewing / Changing Scanning Mode

Typically, the scanning mode for your phone is programmed by your Service Provider. However, you may review the current scanning mode and (if desired) change it by following these procedures.

To Review Scanning Mode

1.Press RCL , . The display will show the current active system choice.

2.Press END to exit without changing selections.

To Change Scanning Modes

1.Press RCL , . The display will show the current active system choice.

2.Repeatedly press or to cycle through the scanning modes.

3.When the desired scan setting appears in the display, press STO .

4.Press END to exit to normal operation.

NOTE Constant ﬂashing of RM, or a steadily lit NS while within your home service area may indicate an unintentional choice has been made. If this occurs, review the System Type to see if the unit is operating in Standard Mode, or if an alternate selection has been made.

44

Image 58

Motorola ENHANCED CELLULAR TELEPHONE owner manual Programming Scanning Modes, Overview, Reviewing / Changing Scanning Mode

Contents

N e r ’s M a n u a l Warranty Expiration Date Date of Purchase Table of Contents Storing Numbers in Memory Advanced Memory Dialing FeaturesSpecial Call Features Placing Calls From Memory Using the Feature Menu Special System FeaturesSelecting and Deselecting Features Cellular System Information Call TimersSecurity Features Programming Scanning Modes Troubleshooting Reference Introduction Vii Viii Introduction Controls and Indicators ➋ Earpiece ➏ Numeric Keypad Xii Prepare the Battery for Initial Use Getting Started Lift the battery off Attach the BatteryRemove the Battery Turn your phone off Using Plug-In Chargers Quick-Change Battery Removal/Replacement Turning Phone On and Off Basic OperationAbout the Antenna Start-up Self Tests NS No Service Indicator Start-up Status IndicatorsIU In Use Indicator RM Roam Indicator Placing a Call To Correct an ErrorWith power on, enter the number you wish to call If Entering More Than 10 Digits Cellular System Busy Automatic RedialingUnsuccessful Call Attempts Complete the Call Receiving a Call Ending a CallPress END Call In Absence Indicator Signal Strength Meter Adjusting Ringer Volume Volume MeterAdjusting Earpiece Volume Low Battery Warning Battery Voltage Meter Press FCN Storing a Phone Number Storing Numbers in MemoryAbout Memory Etc Location entered is displayed to conﬁrm storage Enter the area code and preﬁx you wish to store Press STO Memory Protect FeatureStoring an Area Code and Preﬁx Postscripting Etc Deleting a Memory Entry Changing a Memory Entry About Recalling from Memory Placing Calls From MemoryPlacing Calls by Entering Two-Digit Number Placing Calls by Scrolling Last Number Redial Advanced Memory Dialing FeaturesTurbo Dial Feature Recalling Last Number Called Super Speed Dial Feature Priority Call Scratch Pad Memory Two-Part Tone Dialing Memory Linking Example of Memory Linking Enter the PIN number and # sign Or recall it from memory location RCL , x Create a pauseEnter the account number and # sign Press RCL , SND to send each remaining number group Microphone Muting Special Call FeaturesDisplay Own Phone Number Automatic Answer Hands Free Operation Multiple Key AnswerDistinctive Ringer Multiple Language Display Extended Talk Time Calling Line ID Special System FeaturesAbout Special System Features Receiving Calls with Calling Line ID Recalling/Viewing Calling Line ID Messages Placing a Call to a Calling Line ID Number Deleting an Individual Message Other Messaging ServicesStoring a Calling Line ID Number in Memory Deleting All Messages Reminder Beeps Placing a Call using PIN OperationVOX Operation PIN Code Operation Special System Features About the Feature Menu Using the Feature MenuSelecting and Deselecting Features Distinctive Ringer Automatic Display TimerOne Minute Beep Automatic Answer Reminder Beeps VOX modeExtended Talk Time Language Select Alternate Status Review Calloff Individual Call Timer Call TimersAbout Timers Resettable Call Timer Automatic Display Timer Electronic Lock Security FeaturesAbout Security Codes To Lock Changing the Unlock Code Setting Outgoing Call RestrictionsDisplaying the Unlock Code Automatic Lock Description Display Cellular System Information Service AreaWeak Signal Alert Cellular System Overview Switchhook and Advanced System Services Roaming Two-System Operation System Type and Phone Number Display Programming Scanning Modes Reviewing / Changing Scanning ModeTo Review Scanning Mode Overview Scanning Modes SCAn mode, press Troubleshooting Before Calling For Service Regulations and Precautions Reference Reference Message Glossary Cumul Full REMind MSgOFF Reminder Beeps feature disabled REMind MSg On Index Reference Reference Volume Meter VOX Operation Weak Signal Alert Why the concern? Reference Reference Reference Where can I find additional information? Patent Information PAT02250 Quick Reference Card Rbrc