Manuals / Motorola / Communications / Two-Way Radio

Motorola XTNi Series manual Install Remove, Power Supply, Adaptors and Drop-in Tray Charger

Models: XTNi Series

1 69

Download 69 pages 6.27 Kb

Page 18

BATTERIES AND CHARGERS

Power Supply, Adaptors and Drop-in Tray Charger

Power Supply

Drop-in Tray Charger

Adaptor

Adaptor

Your radio comes with one Drop-in Tray Charger, one Power Supply (also known as "transformer") and a set of adaptors.

Your power supply, has a "switchable" capability which allows to suit any of the adaptors that comes with your radio package. The adaptor you should choose to install depends on the region you're located.

Once you have identified the adaptor that matches your electrical outlet, proceed to install it as follows:

English 16

Power Supply

Power Supply

Install Remove

•Slide down the adaptor grooves into the power supply until it snaps into place.

•Slide the adaptor upward to remove.

Note: The adaptor shown in the pictures are just for illustration purposes. The adaptor you should install may be different.

Image 18

Motorola XTNi Series manual Install Remove, Power Supply, Adaptors and Drop-in Tray Charger

Contents

Page Page Contents Programming Features Getting StartedAccessories ContentsComputer Software Copyrights Computer Software CopyrightsSafety SafetyBatteries and Chargers Safety Information Batteries and Chargers Safety InformationOperational Safety Guidelines Radio Overview Parts of the RadioRadio Radio Overview Lithium-Ion Li-Ion Battery Side ButtonsModel Frequency Transmit Power Number Antenna Band Batteries and Chargers Battery Features and Charging OptionsAbout the Li-Ion Battery Batteries and ChargersBattery Recycling and Disposal Battery Latchbattery latch Slots Turn OFF the radio Batteries and Chargers Install Remove Power Supply, Adaptors and Drop-in Tray ChargerInstalling Spring Action Belt Clip Battery Life InformationFollowing chart summarizes battery life estimations Charging the Battery Charging with the Drop-in Tray Single Unit ChargerCharging a Stand-Alone Battery Charging a Standard Battery Adjustable bracket Standard High and Ultra High Capacity Charging a High Capacity Battery Drop-in Tray Charger LED Indicators Standard Charger LED IndicatorEstimated Charging Time MUC LED Indicator Getting Started Adjusting VolumeGetting Started Turning Radio ON/OFFSelecting a Channel Talking and MonitoringReceiving a Call Signal Strength Indicator and Channel Busy Indicators Talk RangeGetting Started Getting Started Radio LED Indicators Radio Status LED IndicationWith Compatible VOX Accessories HANDS-FREE USE/VOXHands Free without Accessories iVOX Battery SaveReset To Factory Defaults Keypad Beeps Setting VOX/iVOX SensitivityEnd of Transmission Tone Roger Beep Tone Menu OptionsSetting VOX / iVOX sensitivity IVOGetting StartedImic YES Programming Features Entering Programming ModeProgramming Features Programming RX Reception FrequenciesProgramming RX Reception Codes CTCSS/DPL RX BW Programming RX Reception BandwidthProgramming Scramble L Programming Maximum Number of ChannelsMA X CH Programming Call TonesProgramming Microphone Gain Level YES Programming Scan ListProgramming Buttons Editing Channel Alias Name Nuisance Channel Delete Time-Out Timer CPS Computer Programming SoftwareBandwidth Select Battery Type Setting Call TonesScramble Programming Features Cloning Radios Cloning with a Multi-Unit Charger MUCTurn on the Target radio and place it Into one of the SUCs What to do if cloning fails Cloning Radios using the CPS Computer Programming Software Troubleshooting TroubleshootingDoes not come on Cannot activate VOX USE and Care If the radio is submerged in waterUSE and Care Frequency and Code Charts Frequency and Code ChartsChannel Radios PMR 446 Defaults Ctcss DPL Codes 108 627 115 712 What is not Covered by the Warranty WarrantyWarranty Information Motorola LimitedMotorola Limited Warranty Accessories Chargers Page 6871663M05