Manuals / Moyer Diebel / Kitchen Appliance / Dishwasher

Moyer Diebel 301HT M2 installation manual Electrical Connections

Models: 301HT M2

1 50

Download 50 pages 12.29 Kb

Page 11

Installation

Electrical Connections

Note:

Leave enough electrical cable behind the machine so that the dishwasher can be pulled forward a minimum of two feet to be serviced.

Warning:

Electrical and grounding connections must comply with all local electrical codes or in the absence of local codes then connections must comply with the National Electrical Code.

Warning: When working on the dishwasher, disconnect the main electric service and tag it to indicate work is being done on that circuit.

1.The electrician should compare the electrical specifications on the machine electrical data plate (located in the control panel) to the electrical power supply before connecting the machine to the incoming service at a fused disconnect switch.

IMPORTANT: The 208-240V/60Hz/1PH electrical supply service for this machine must be a 2-wire plus ground service. For optional 208-240V/60Hz/3PH the electrical supply service must be a 3-wire plus ground service.

2.On the 208V-240V models, a knockout is provided at the rear of the junction box for electrical service connections. A fused disconnect switch or circuit breaker (supplied by user) is required to protect each power supply circuit.

Refer to the MACHINE ELECTRICAL CONNECTION DATA PLATE for the dishwasher power requirements.

3

Image 11

Moyer Diebel 301HT M2 installation manual Electrical Connections

Contents

301HT M2 Undercounter High Temperature DishwasherInstallation Manual with Service Replacement Parts Manual P/N 114150 rev. BModel Number Serial Number VoltageHertz Phase FIRST-CLASS MAIL PERMIT NO. 2101 WINSTON-SALEM, NC BUSINESS REPLY MAILMOYER DIEBEL PO BOX 4183 WINSTON-SALEM, NC NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATESThis Card Must Be Returned to Validate Machine Warranty WARRANTY REGISTRATION CARDWARRANTY REGISTRATION CARD This Card Must Be Returned to Validate Machine WarrantySerial Number Revision HistoryRevision RevisedLimited Warranty Limited WarrantyService Replacement Parts Table of ContentsInstallation Operation Cleaning De-liming Maintenance TroubleshootingOptions Model DescriptionsModel 301HT M2 Receiving Receiving installationElectrical Connections Drain Connections Plumbing ConnectionsWater Connections Chemical Dispensers Completing the InstallationDetergent Rinse AidInitial Start-up Initial Start Up1. The door must be closed to begin the cycle Initial Start UpNote DO NOT OVERLOAD the rack Operation ProceduresOperation This procedure is only needed when the tank is emptyWeekly CleaningAfter Meal Periods or 8 Hours of Operation Danger De-limingDe-liming Procedure Monthly Maintenance MaintenanceCleaning Schedule Daily MaintenanceCause TroubleshootingSolution ConditionKeep wash water as clean as possible TroubleshootingSolution Wash water temperature too lowBlank Page This Page Intentionally Left BlankPage Service Replacement PartsIllustrations Hood and Tank Assembly Unit Item NoDescription Door Assembly H25791 Rinse-aid Wash Tank Heater and Chemical Dispenserspump DetergentSqueeze Tube, Rinse comes with black fittings Squeeze Tube, Detergent comes with black fittingsFill Piping Assembly H36156 1614 Drain AssemblyTo Drain H32796 BOTTOM OF TAN Wash and Rinse Piping Assembly0502563 Wash and Rinse Arm Assemblies Bearing, Wash Arm Wash Pump/Motor Assembly H36354 Booster Heater Assembly H36250 Control Panel Assembly Beginning with S/N 66190 and above Start Switch Push button only does not include ItemThermometer Does not include Item Control Cabinet Assembly H160121 Blank Page This page intentionally left blankElectrical Schematics and Timing Chart Electrical Schematic and Timing ChartElectrical Schematic Timing Chart