Manuals / Moyer Diebel / Kitchen Appliance / Dishwasher

Moyer Diebel 301HT M2 Plumbing Connections, Water Connections, Drain Connections

Models: 301HT M2

1 50

Download 50 pages 12.29 Kb

Page 12

Plumbing Connections

Installation

Plumbing Connections

Water Connections

1.Connect the hot water supply to the fill hose provided with a 3/4" NPT fitting.

2.Install a manual shut-off valve in the water supply line to accommodate servicing the machine. The shut-off valve should be the same size or larger than the supply line and installed as close to the dishwasher as possible.

3.Install a 3/4" pressure reducing valve (PRV) (supplied with machine) in the water supply line, and set at 20-22 PSI/138-151kPa. Install the PRV downstream from the service shut-off valve and as close to the dishwasher as possible.

Drain Connections

1.Drain hose must be supported by bracket provided (shipped inside of machine).

2.The drain hose bracket must be mounted a minimum of 2 feet above the finished drain, either on the rear of the machine or on the wall.

3.The maximum height of the drain from the floor must not exceed 3 feet.

4.Connect the 3/4"I.D. flexible drain hose to a 1-1/2" wye (Y) drain fitting. Use a 3/4" hose

Note:

Plumbing connections must comply with local health and plumbing codes.



Connect machine flexible		Do not connect the machine
drain hose to a wye fitting.		flexible drain hose to a
		90° fitting.

4

Image 12

Moyer Diebel 301HT M2 installation manual Plumbing Connections, Water Connections, Drain Connections

Contents

Undercounter High Temperature Dishwasher Installation Manual with Service Replacement PartsManual P/N 114150 rev. B 301HT M2Model Number Serial Number VoltageHertz Phase BUSINESS REPLY MAIL MOYER DIEBEL PO BOX 4183 WINSTON-SALEM, NCNO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES FIRST-CLASS MAIL PERMIT NO. 2101 WINSTON-SALEM, NCWARRANTY REGISTRATION CARD WARRANTY REGISTRATION CARDThis Card Must Be Returned to Validate Machine Warranty This Card Must Be Returned to Validate Machine WarrantyRevision History RevisionRevised Serial NumberLimited Warranty Limited WarrantyTable of Contents InstallationOperation Cleaning De-liming Maintenance Troubleshooting Service Replacement PartsModel Descriptions Model 301HT M2Options Receiving installation ReceivingElectrical Connections Plumbing Connections Water ConnectionsDrain Connections Completing the Installation DetergentRinse Aid Chemical DispensersInitial Start Up Initial Start-upInitial Start Up 1. The door must be closed to begin the cycleOperation Procedures OperationThis procedure is only needed when the tank is empty Note DO NOT OVERLOAD the rackCleaning After Meal Periods or 8 Hours of OperationWeekly De-liming De-liming ProcedureDanger Maintenance Cleaning ScheduleDaily Maintenance Monthly MaintenanceTroubleshooting SolutionCondition CauseTroubleshooting SolutionWash water temperature too low Keep wash water as clean as possibleThis Page Intentionally Left Blank Blank PageService Replacement Parts IllustrationsPage Hood and Tank Assembly Item No DescriptionUnit Door Assembly H25791 Wash Tank Heater and Chemical Dispensers pumpDetergent Rinse-aidSqueeze Tube, Detergent comes with black fittings Squeeze Tube, Rinse comes with black fittingsFill Piping Assembly H36156 Drain Assembly To Drain1614 H32796 Wash and Rinse Piping Assembly BOTTOM OF TAN0502563 Wash and Rinse Arm Assemblies Bearing, Wash Arm Wash Pump/Motor Assembly H36354 Booster Heater Assembly H36250 Control Panel Assembly Start Switch Push button only does not include Item Thermometer Does not include ItemBeginning with S/N 66190 and above Control Cabinet Assembly H160121 This page intentionally left blank Blank PageElectrical Schematic and Timing Chart Electrical Schematics and Timing ChartElectrical Schematic Timing Chart