Manuals / MTD / Lawn and Garden / Snow Blower

MTD 60-3753-6, 60-3754-4 manual Skid Shoes, Drive Control, Auger Control, Figure

Models: 60-3753-6 60-3754-4

1 52

Download 52 pages 37.51 Kb

Page 15

Figure 19- Skid Shoes

.

Figure 17

Drive Control

When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

Check the adjustment of the drive control as follows:

1.	With the drive control disengaged,
	push the snow thrower gently
	forward. The unit should roll freely.
2.	Engage the drive control and gently
	attempt to push the snow thrower	Disengaged
	forward. The wheels should not turn.
	The unit should not roll freely.

3.With the drive control disengaged, move the shift lever back and forth between the R2 position and the F6 position several times. There should be no resistance in the shift lever.

If any of the above tests failed, the drive cable is in need of adjustment. refer to Figure 18 and proceed as follows:

•Loosen the hex jam nut on the auger control cable “Z” fitting and rotate the coupling end (without turning the cable) of the cable downward to provide more slack or upward to take up slack. See Figure 18 .

Auger Control

Refer to Auger Control Test on Page 12 to adjust the auger control.

Figure 18

Skid Shoes

NOTE: The space between the skid shoes and the ground can be adjusted. See Figure 19. For close snow removal, place skid shoe in the low position. Use middle or high position when area to be cleared is uneven.

NOTE: Some models are equipped with reversible skid shoes and may be turned over to increase their lifespan. See Figure 19.

CAUTION: Loose gravel can be picked up and thrown by the auger, causing injury to the operator and bystanders and/or damage to the snow thrower and surrounding property.

•Adjust skid shoes by loosening the four hex nuts (two on each side) and carriage bolts. Move skid shoes to desired position.

•Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes. Retighten nuts and bolts securely.

•Retighten the hex jam nut and repeat all three tests to verify proper adjustment has been achieved.

Standard

Reversible

Figure 19- Skid Shoes

15

Image 15

MTD 60-3753-6, 60-3754-4 manual Skid Shoes, Drive Control, Auger Control, Figure

Contents

FOR CUSTOMER ASSISTANCE CALL IMPORTANT: Read safety rules and instructionsModels carefully before operating equipmentENGINE INFORMATION TABLE OF CONTENTSContent FINDING MODEL NUMBEROperation SECTION 1: IMPORTANT SAFE OPERATION PRACTICESTraining PreparationYour Responsibility Maintenance And StorageUnpacking SECTION 2: SETTING UP YOUR SNOW THROWERBefore Assembly Setting up the Snow ThrowerModels with a Chute Directional Control Chute Assembly all modelsFor Models with 4 Way Chute Control Box For Models with 2Way Chute ControlSkid Shoe Chute Clean-outToolFinal Adjustments Lamp Wire optionalOil Fill SECTION 3: KNOWING YOUR SNOW THROWERThrottle Control PrimerChute Directional Control optional Clean-OutToolAuger Control 2 Way Chute Control optionalElectric Starter Outlet If so equipped Chute AssemblyCAUTION: If your home’s wiring system SECTION 4: OPERATING YOUR SNOW THROWERFor models with optional interlock mechanism only Stopping The EngineTo Engage Drive To Engage AugersFigure To Throw SnowOperating Tips Auger Control TestFigure Tire Chains on models so equipped Chute Clean-OutToolDrift Cutters on models so equipped Drift Cutter KitFigure Figure Shift Rod AdjustmentChute Bracket Adjustment SECTION 5 MAKING ADJUSTMENTSSkid Shoes Figure 19- Skid ShoesDrive Control Auger ControlAugers EngineLubrication Shave Plate and Skid ShoesFigure Replacing BeltsAuger Belt Drive BeltFriction Wheel Rubber FigureFigure Figure Figure SECTION 7: OFF-SEASONSTORAGESECTION 8: TROUBLE SHOOTING YARDWORKS 4 YEAR LIMITED WARRANTY ENGINES SECTION 9: YARDWORKS 4 YEAR LIMITED WARRANTYLOGEMENT DES TAILLELAME ENSEMBLE DE LA731-2643 Page 656-0012A 731-04873 Manual Chute Control Commande de la goulotte à 2 fonctionsCommande de la goulotte manuel Commande de la goulotte à 4 fonctionsStyles H, K & L PART pas: couvre ne garantie Cette agéée technique station une à vous DÉPANNAGE DE GUIDE 8: CHAPITREmachine SAISON HORS REMISAGE 7 CHAPITREsilicone de ressorts, chaînes, les particuliersuit comme procédez caoutchouc frottement de roue la decaoutchouc en bague la de Changement 29 Figure24 Figure 27 Figure26 Figure 25 Figure22 Figure courroies les de Remplacementpatins et plate Lame 23 FigureRoues LubrificationMoteur ENTRETIEN ET D’UTILISATION RÉGIME 6: CHAPITREPatins tarière la de Commandetransmission la de Commande goulotte la de support du Réglage15 Figure RÉGLAGES 5 CHAPITREvitesses de levier du Tige Goulottegoulotte la de dégagement de Outil d’utilisation Conseilspneu pour Chaînes coupe de Barres11 Figure de commandeneige la projeter Pour tarière la embrayer Pourêtre peut supplémentaire amorçage Un REMARQUE transmission la embrayer Pourmoteur du Arrêt Il .sùr endroit un dans clé la Rangez REMARQUEFONCTIONNEMENT 4: CHAPITRE GoulotteTarières lanceur à démarreur de Poignéel’entraînement de Commande tarière la de Commandeoption en fonctions 2 à goulotte la de Commande option en fonctions 4 à goulotte la de CommandeAmorceur moteur de CommandesSOUFFLEUSE LA DE COMMANDES 3: SECTION l’obturateur de Commandeneige la de dégagement de Outil 9 Figure8 Figure 5 Figure «Réglage» chapitre le dans goulotte»7 Figure 6 Figuresouffleuse la de Assemblage de changement du commande de tige la correctementinstallé MONTAGE 2: CHAPITREresponsabilité Votre UTILISATION REMISAGE ET ENTRETIENSÉCURITÉ DE CONSIGNES IMPORTANT 1: CHAPITRE PréparationFormation MODÈLE DE NUMÉRO LE TROUVER POUR VENTE-APRÈSSERVICEMOTEUR DE INFORMATION MATIÈRES DES TABLE5218-523-866-1AU VENTE APRÉS SERVICE LE APPELEZ 4-3754-606-3753-60 Modèles