GLOBUG LIGHTING SYSTEM — MAINTENANCE

For a prolonged life cycle an extended quality follow the recommended GloBug service guidelines as referenced in Table 3.

TABLE 3. PERIODIC CHECK AND MAINTENANCE

FIGURE

PART

 

 

CHECK ITEM

SOLUTION

 

 

 

 

 

 

 

 

 

L1

Frame Pipe

 

Frame pipe skewed?

Replace.

 

 

 

 

 

 

 

 

L2

Lamp Holder

 

Lamp holder loose?

Tighten or replace.

Lamp

 

 

 

 

 

 

L3

Lamp (Base)

 

Lamp base loose?

Screw in securely.

 

 

 

 

 

 

 

 

L4

Lamp

 

Defective lamp?

Replace.

 

 

 

 

 

 

 

L5

Cable/Connector

Cable disconnected or loose?

Connect securely.

 

 

 

 

 

 

 

B1

Balloon (Envelope)

Defective or dirty?

Replace.

 

 

 

 

 

 

 

 

Balloon

B2

Zipper

 

Broken?

 

Replace.

 

 

 

 

 

 

 

B3

Fan Motor (Blower)

Working properly?

Repair or replace.

 

 

 

 

 

 

 

M1

Mast Sliding Surface

Slides smoothly?

Apply grease.

 

 

 

 

 

 

 

 

 

M2

Wire Rope

 

Damaged?

 

Apply grease or replace.

 

 

 

 

 

 

Mast

M3

Wire Rope End

Is wire end damaged (caulking)?

Replace.

 

 

 

 

 

 

 

 

M4

Winch

 

Defective winch brake ?

Repair or replace.

 

 

 

 

 

 

 

 

M5

Safety Stop

 

Safety latch defective?

Repair or replace.

 

 

 

 

 

 

 

C1

Counter-Weight

Travels smoothly?

Spray grease.

 

 

 

 

 

 

 

 

C2

Outriggers

 

Travels smoothly?

Spray grease.

 

 

 

 

 

 

 

C3

T-handle and Wheels

Proper movement.

Tighten securely.

 

 

 

 

 

 

 

C4

Bolt for Handle

Check if bolt is not loose.

Tighten securely.

 

 

 

 

 

 

 

 

C5

Brake Pedal

 

Linkage working correctly.

Check, spray grease

 

 

 

 

 

 

 

Cart

C5

Brake Pedal

 

Notch worn-out?

Replace.

 

 

 

 

 

 

 

 

C6

Hanger

 

Check if the installation is not loose.

Fasten securely.

 

 

 

 

 

 

 

C7

Front Wheel Pivot

Turns smoothly?

Check, apply grease.

 

 

 

 

 

 

 

 

C8

Tires

 

Tire pressure 35.5 psi (294 kPa)?

Adjust.

 

 

 

 

 

 

 

C9

Link for Front Shaft

Linkage moves smoothly?

Spray grease.

 

 

 

 

 

 

 

 

C10

Brake

 

Working properly?

Adjust.

 

 

 

 

 

 

 

Electric

E1

Power Cable

 

Defective or worn cable?

Replace.

 

 

 

 

 

 

 

E2

Non-load Voltage

Is generator output 125 VAC?

Adjust or replace generator.

 

 

 

 

 

 

 

 

 

 

- Daily Check

- Every 20 Hours

- Every 100 hours

- Every 500 hours

 

GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV. #3 (03/22/06) — PAGE 37

Page 37
Image 37
Multiquip GB114BC manual Globug Lighting System Maintenance