assembly and installation

Assembly and Installation

Before the trowel can be put into operation there are some components that must be installed before the trowel can be used.This section provides general instructions on how to install those components. Instruction sheet P/N 20485 provides further details for the handle assembly.

Handle Tube Installation

13.Attach the main handle (tube) to the gearbox as shown in (Figure 4). The mounting hardware should be contained in the shipping container.

MAIN HANDLE

(TUBE)

3/8 FLAT WASHER

3/8-16

NYLOC NUT

3/8-16 X 3.25 HHC SCREW

GEARBOX

Figure 4. Handle Tube Installation

Vibratory T-Handle Bar Placement

1.The vibratory T-handle bar is already attached to the main handle tube.

2.To adjust the height of the T-bar, loosen the star wheel (Figure 5) and position T-handle bar in the desired position.

T-HANDLE BAR

HEIGHT

ADJUSTMENT

STAR WHEEL

Figure 5. T-Handle Bar Adjustment

NOTICE

If additional handle height adjustment is desired, a handle wedge kit can be purchased for your trowel by ordering P/N 2576 from your Multiquip dealer.

These wedges are placed between the handle and the gearbox to adjust the operating height of the handle. This kit comes complete with wedges, new bolts and installation instructions. This will move your operating handle position up or down approximately 3” (76 mm).

Throttle Cable Installation (Engine)

1.Uncoil the throttle cable and housing.

2.Feed the throttle cable through the cable housing.

3.Connect the trowel throttle cable to the engine throttle linkage (Figure 6). There should be a piece of wire installed on the trowel to show where to route the throttle cable.

4.Route cable end through the cable locking screw. When connecting the cable housing, make sure that no more than 1/4" (6.4 mm) of the cable housing protrudes past the housing clamp on the engine.

ENGINE

THROTTLE

LEVER

 

CABLE

THROTTLE

LOCKING

CABLE

SCREW

 

1/4”

 

(6.35 MM)

CABLE HOUSING

CLAMP/SCREW

Figure 6. Throttle Cable Installation (Engine)

5.Tighten cable clamp screw.

6.After the trowel throttle cable has been connected to the engine throttle linkage, adjust and tighten operator position of the T-bar handle to lock the throttle cable at the proper length.

3. Tighten star wheel firmly.

j36s60 WALK-BEHIND TROWEL • operatION And parts manual — rev. #1 (01/23/13) — page 17

Page 16 Page 18
Page 17
Image 17
Multiquip J36S60 manual Assembly and installation, Assembly and Installation, Handle Tube Installation
Page 16 Page 18

J36S60 specifications

The Multiquip J36S60 is a versatile and robust generator designed for various applications, ranging from construction sites to outdoor events. With a focus on reliable power and durability, the J36S60 is engineered to meet the demanding requirements of professionals and contractors alike.

At the heart of the J36S60 is its powerful engine, which provides a maximum output of 36 kVA. This generator is equipped with a 60Hz, 240V output, making it suitable for a wide range of equipment and tools. The J36S60 features a fuel-efficient design, allowing for extended run times that minimize downtime on job sites. It can operate for hours on end, ensuring that you have continuous power for critical tasks.

One of the standout features of the J36S60 is its state-of-the-art control panel. The intuitive control panel provides clear access to various functions, making it easy for users to monitor power output, fuel levels, and maintenance intervals. The panel includes circuit breakers, hour meters, and an easy-to-read digital display, ensuring that operators have all necessary information at their fingertips.

Additionally, the Multiquip J36S60 generator incorporates advanced technologies for noise reduction and fuel efficiency. Its innovative design includes sound-dampening materials and a high-capacity silencer, resulting in quieter operation compared to traditional generators. This feature makes it especially suitable for urban environments where noise regulations are strictly enforced.

The J36S60 is built with durability in mind. The heavy-duty steel frame and powder-coated finish ensure that it can withstand the rigors of demanding job sites and adverse weather conditions. Furthermore, the unit is designed for easy transport, with integrated lifting hooks and a compact design that allows for convenient positioning and relocation.

Safety is a priority with the J36S60, which comes equipped with multiple safety features including low oil shutdown, overload protection, and an emergency stop button. These safety mechanisms ensure that both the operator and the machinery are protected during operation.

Overall, the Multiquip J36S60 is a high-performance generator that excels in providing reliable power in a variety of settings. Its combination of power output, efficient fuel consumption, user-friendly controls, and robust build quality makes it an excellent choice for construction professionals, event coordinators, and anyone in need of dependable portable power.
Top Page Image Contents