MAINTENANCE
CAUTION
Inspection and other services should always be carried out on hard and level ground with the engine shutdown.
Inspection and Maintenance ServiceTables.
1.To make sure your plate compactor is always in good working condition before using, carry out the maintenance inspection in accordance with Tables 5 through 7.
TABLE 5. MVH-306D/DS MACHINE INSPECTION
ITEM | HOURS OF | REMARKS | |
OPERATION | |||
|
| ||
|
|
| |
Loose or Missing | Every 8 hours |
| |
Screws | (every day) |
| |
|
|
| |
Damaged Parts | Every 8 hours |
| |
(every day) |
| ||
|
| ||
|
|
| |
Function of Controlling | Every 8 hours |
| |
System Part | (every day) |
| |
|
|
| |
Hydraulic System Leak | Every 100 hours | See page 21 | |
|
|
| |
Vibrator Oil Check | Every 100 hours | See page 23 | |
|
|
| |
Vibrator Oil | Every 300 hours | See page 23 | |
Replacement | |||
|
| ||
|
|
| |
Hydraulic Oil Check | Every 100 hours | See page 23 | |
|
|
| |
Hydraulic Oil | First after 200 |
| |
hours, then every | See page 23 | ||
Replacement | |||
1,000 hours |
| ||
|
| ||
|
|
| |
Every 200 hours | See page 22 | ||
|
|
| |
Battery Check | Every 100 hours | See page 24 | |
|
|
|
NOTICE
Fuel piping and connections should be replaced every 2 years.
TABLE 6. MVH-306D/DS ENGINE CHECK
ITEM | HOURS OF OPERATION | |
|
| |
Oil or Fuel Leak | Every 8 hours (every day) | |
|
| |
Tightness of Fastening | Every 8 hours (every day) | |
Threads | ||
| ||
|
| |
Engine Oil Check and | Every 8 hours (every day) | |
(Replenish to specified maximum | ||
Replenishment | ||
level) | ||
| ||
|
| |
Engine Oil Replacement | After first 25 hours then every 50 to | |
100 hours | ||
| ||
|
| |
Air Filter Cleaning | Every 100 hours | |
|
|
See separate engine manual for details on engine check.
Daily Service
Check for leakage of fuel or oil.
Check for loose screws including tightness. See Table 7 below (tightening torque ), for retightening:
TABLE 7.
TIGHTENING TORQUE (in. kg/cm) Diameter
Material | 6mm | 8mm | 10mm | 12mm | 14mm | 16mm | 18mm | 20mm |
|
|
|
|
|
|
|
|
|
4T | 70 | 150 | 300 | 500 | 750 | 1,100 | 1,400 | 2,000 |
|
|
|
|
|
|
|
|
|
100 | 250 | 500 | 800 | 1,300 | 2,000 | 2,700 | 3,800 | |
|
|
|
|
|
|
|
|
|
11T | 150 | 400 | 800 | 1,200 | 2,000 | 2,900 | 4,200 | 5,600 |
|
|
|
|
|
|
|
|
|
* | 100 | 300~ | 650 ~ |
|
|
|
|
|
350 | 700 |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
* (In case
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt, and screw.
CAUTION
These inspection intervals are for operation under normal conditions.Adjustyour inspection intervals based on the number hours plate compactor is in use, and particular working conditions.
Remove soil and clean the bottom of compaction plate.
Check hand pump, piping and hose for any leakage. A loosened hydraulic hose can be a cause for leakage. Check hydraulic hose connections with wrench applied for tightness.
Check engine oil.
MVH306D/DS PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #11 (02/04/14) — PAGE 21
