Napoleon Fireplaces BGD90NT, BGD90PT Operating Instructions, For Your Safety Read Before Lighting

25

OPERATING INSTRUCTIONS

When lit for the fi rst time, the fireplace will emit a slight odor for a few hours. This is a normal temporary condition caused by the curing of the paints and lubricants used in the manufacturing process and will not occur again. Simply open a window to suffi ciently ventilate the room.

After extended periods of non-operation such as following a vacation or a warm weather season, the fi replace may emit a slight odor for a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to suffi ciently ventilate the room.

Purge all gas lines with the glass door of the fireplace removed. Assure that a continuous gas flow is at the burner before installing the door.

FOR YOUR SAFETY READ BEFORE

LIGHTING:

A.This fi replace is equipped with a pilot which must be lit by hand while following these instructions exactly.

B.Before operating smell all around the fi replace area for gas and next to the fl oor because some gas is heavier than air and will settle on the fl oor.

C.Use only your hand to turn the gas control knob / manual shut-off knob. Never use tools. If the knob will not turn by hand, do not try to repair it. Call a qualifi ed service technician. Force or attempted re pair may result in a fi re or explosion.

D.Do not use this fi replace if any part has been under water. Immediately call a qualifi ed service technician to inspect the fi replace and replace any part of the control system and any gas control which has been under water.

WHAT TO DO IF YOU SMELL GAS

•Do not touch any electric switch.

•Do not use any phone in your building.

•If you cannot reach your gas supplier, call the fi re department.

• Turn off all gas to the fi replace.	FIGURE 65
• Do not try to light any appliance.
• Immediately call your gas supplier		L
from a neighbor’s phone. Follow the	I		O
	P			T

gas supplier’s instructions.

WARNING: if you do not follow these	F	O
	F	N
instructions exactly, a fi re or explosion may	O

result causing property damage, personal
injury or loss of life. Initial lighting of the pilot
and main burners must be done with the	GAS KNOB
glass door off.

LIGHTING INSTRUCTIONS

Do not connect valve or wall switch to electricity. See installation instructions.

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob it depressed slightly.

1.STOP! Read the safety information on the operating label.

2.Turn off all electric power to the fi replace.

3.Turn the gas knob clockwise to off.

4.Wait 5 minutes to clear out any gas. If you smell gas, including near the fl oor, STOP! Follow “B” on the operating label. If you don’t smell gas, go to the next step.

5.If the fi replace is equipped with a fl ame adjustment valve, turn clockwise to off.

6.Find pilot located in front of the back log on the right.

7.Turn gas knob counter-clockwise to pilot.

8.This unit is equipped with an auto-spark. Depress and hold gas knob . Keep knob fully depressed for one minute, then release. If pilot does not continue to burn repeat steps 3 through 7.

9.With pilot lit, push and turn gas knob counter-clock

wise to on.

10.If equipped with fl ame adjustment valve, turn knob to high.

11.If equipped with remote on-off switch, main burner may not come on when you turn the valve to on or high. Remote switch must be in the on position to ignite burner.

12.Turn on all electric power to the fi replace.

FIGURE 66

TO TURN OFF GAS

1.Turn off all electric power to the fi replace if service is to be performed.

2.For a complete shut-down procedure: push in gas control knob

slightly and turn clockwise to off. Do not force.

3.For a temporary shut-down procedure: set the switch to off.

Press and turn the gas knob clockwise to pilot.

TURN OFF THE GAS AND ELECTRICAL POWER BEFORE

SERVICING THE FIREPLACE.

W415-0580 / C / 04.07.08