National Instruments 5411 Optional Equipment, Cabling

Chapter 1 Introduction

©

National Instruments Corporation 1-5 DAQArb 5411 Use r Manual

Optional Equipment

National Instruments offers a variety of products to use with your

DAQArb 5411, including probes, cables, and other accessor ies, as

follows:

• Shielded and unshielded I/O connector blocks (SCB-68, TBX-68,

CB-68)

•RTSI bus cables

For more specific information about these products, refer to your

National Instruments catalogue or web site, or call the office

nearest you.

Cabling

The following list gives recommended part numbers for cables that you

can use with your 5411 device:

• BNC male to BNC male, 50 Ω cable from ITT Pomona El ectro nics

(part number BNC-C-xx)

• BNC male to BNC male, 75 Ω cable from ITT Pomona El ectro nics

(part number 2249-E-xx)

• BNC female to RCA phono plug adapter, from ITT Pomona

Electronics (part number 5319)

•BNC 50 Ω feed-through terminator adapter from ITT Pomona

Electronics (part number 4119-50)

• BNC female-female adapter from ITT Pomona Electronics

(part number 3283)

Contents

Main Page Important Information Warranty Copyright Trademarks WARNING REGARDING MEDICAL AND CLINICAL USE OF NATIONAL INSTRUMENTS PRODUCTS Page Chapter 4 Arb Operation Page Tables About This Manual Organization of This Manual Conventions Used in This Manual Customer Communication Introduction About Your DAQArb 5411 What You Need to Get Started Software Programming Choices National Instruments Application Software NI-DAQ Driver Software Optional Equipment Cabling Unpacking Installation and Configuration Installation Hardware Configuration Installing the Optional Memory Module Signal Connections I/O Connector ARB Connector = x 10 V V R + R SYNC Connector PLL Ref Connector Page Chapter 3 Signal Connections National Instruments Corporation 3-5 DAQArb 5411 Use r Manual Figure 3-4. DAQArb 5411 50-Pin Digital Output Connector Pin Assignments Signal Descriptions SHC50-68 50-Pin Cable Connector Chapter 3 Signal Connections National Instruments Corporation 3-7 DAQArb 5411 Use r Manual Figure 3-5. SHC50-68 68-Pin Connector Pin Assignments Power-Up and Reset Conditions National Instruments Corporation 4-1 DAQArb 5411 Use r Manual Arb Operation This chapter describes how to use your DAQArb 5411. Figure 4-1 shows the DAQArb 5411 block diagram. Figure 4-1. DAQArb 5411 Block Diagram Waveform Generation Update Rate Arb Mode Waveform Size and Resolution Waveform Memory Minimum Buffer Size and Resolution Waveform Linking and Looping Chapter 4 Arb Operation National Instruments Corporation DAQArb 5411 User Manual 4-6 Waveform Staging Page Direct Digital Synthesis (DDS) Mode Page Frequency Resolution and Lookup Memory Frequency Hopping and Sweeping Triggering Trigger Sources Modes of Operation Single Trigger Mode Continuous Trigger Mode Stepped Trigger Mode Burst Trigger Mode Marker Output Signal Page Analog Output SYNC Output and Duty Cycle Output Attenuation Output Impedance Output Enable Pre-attenuation Offset Phase-Locked Loops ! Master/Slave Operation a. RTSI Bus Master/Slave Configuration Device b. External Master Analog Filter Correction Digital Pattern Generation Page RTSI Trigger Lines Calibration A Specifications Analog Output Voltage Output Sine Spectral Purity Filter Characteristics Waveform Specifications Timing I/O Page Marker Output Digital Pattern Output External Clock Reference Input Internal clock Mechanical B Waveform Sampling and Interpolation Page C Customer Communication FTP Support Electronic Services Bulletin Board Support Telephone and Fax Support Telephone Fax Fax-on-Demand Support E-Mail Support (currently U.S. only ) Technical Support Form DAQArb 5411 Hardware and Software Configuration Form National Instruments Products Other Products Documentation Comment Form Title: Edition Date: Part Number: Mail to: Technical Publications Fax to: Technical Publications Glossary Numbers/Symbols A B C D Page E F G H I K L M N O P R S T U V W Index Numbers A B C D E F H I L N O P R S T U V W