National Instruments NI PCI-6110, NI PCI-6111 Connecting Signals

© National Instruments Corporation 4-1 NI PCI-6110/6111 User Manual

4

Connecting Signals

This chapter describes how to make input and output signal connections to

the NI PCI-6110/6111 through the device I/O connector. Table4-1 shows

the cables that can be used with the I/O connectors to connect to different

accessories.

I/O Connector

Figure4-1 shows the pin assignments for the 68-pin I/O connector on the

NI PCI-6110/6111. A signal description follows the connector pinouts.

Figure4-2 shows the pin assignments for the NI PCI-6110/6111 when used

with a 50-pin accessory.

Caution Connections that exceed any of the maximum ratings of input or output signals

on the NI PCI-6110/6111 can damage the device and the computer. Maximum input ratings

for each signal are given in the Protection column of Table4-3. NI is not liable for

anydamage resulting from such signal connections.

Table 4-1. I/O Connector Details

Device with

I/O Connector

Number

ofPins

Cable for

Connecting

to100-Pin

Accessories

Cable for

Connecting

to 68-Pin

Accessories

Cable for

Connecting

to50-Pin

Accessories

NI PCI-6110,

NI PCI-6111

68 N/A SH68-68EP,

SH68-68R1-EP

SH6850

Contents

Main Page Important Information Warranty Copyright Trademarks Patents Compliance FCC/Canada Radio Frequency Interference Compliance Determining FCC Class FCC/DOC Warnings Class A Contents Chapter 4 Connecting Signals Page About This Manual Conventions National Instruments Documentation Related Documentation Introduction About the NI PCI-6110/6111 What You Need to Get Started Software Programming Choices NI-DAQ National Instruments ADE Software Optional Equipment Custom Cabling Unpacking Safety Information Page Page Installing and Configuring the NI PCI-6110/6111 Installing the Software Installing the Hardware Configuring the Device National Instruments Corporation 3-1 NI PCI-6110/6111 User Manual Hardware Overview DAQ - STC RTSI Bus Figure 3-1. NI PCI-6110 Block Diagram I/O Connector Analog Input Input Mode Note The inputs are differential only in the sense that the ground loops are broken. The I/O Connector RTSI Bus Input Polarity and Input Range Considerations for Selecting Input Ranges Input Coupling Analog Output Analog Trigger Figure 3-3. Analog Trigger Block Diagram for the NI PCI-6110 Figure 3-4. Analog Trigger Block Diagram for the NI PCI-6111 Page Page Digital I/O Timing Signal Routing Page Programmable Function Inputs Device and RTSI Clocks RTSI Triggers Connecting Signals I/O Connector Figure 4-1. 68-Pin I/O Connector Pin Assignment for the NI PCI-6110/6111 Figure 4-2. 50-Pin Connector Pin Assignments for the NI PCI-61 10/6111 I/O Connector Signal Descriptions Table 4-2. Signal Descriptions for I/O Connector Pins Page Page Table 4-3. I/O Signal Summary for the NI PCI-6110/6111 Table 4-3. I/O Signal Summary for the NI PCI-6110/6111 (Continued) Connecting Analog Input Signals Types of Signal Sources Floating Signal Sources Ground-Referenced Signal Sources Differential Measurements Differential Connection Considerations Differential Connections for Ground-Referenced Signal Sources Figure 4-4. Differential Input Connections for G round-Referenced Signals Differential Connections for Nonreferenced or Floating Signal Sources Common-Mode Signal Rejection Considerations Working Voltage Range Analog Output Signal Connections Digital I/O Signal Connections Power Connections Timing Connections Programmable Function Input Connections DAQ Timing Connections TRIG1 Signal TRIG2 Signal Page STARTSCAN Signal Page CONVERT* Signal AIGATE Signal SISOURCE Signal SCANCLK Signal EXTSTROBE* Signal Waveform Generation Timing Connections WFTRIG Signal UPDATE* Signal UISOURCE Signal General-Purpose Timing Signal Connections GPCTR0_SOURCE Signal GPCTR0_GATE Signal GPCTR0_OUT Signal GPCTR0_UP_DOWN Signal GPCTR1_SOURCE Signal GPCTR1_GATE Signal GPCTR1_OUT Signal GPCTR1_UP_DOWN Signal Page FREQ_OUT Signal Field Wiring Considerations Page Calibration Loading Calibration Constants Self-Calibration External Calibration A Specifications Analog Input Input Characteristics Accuracy Information Transfer Characteristics Amplifier Characteristics Dynamic Characteristics Stability Analog Output Output Characteristics Transfer Characteristics Voltage Output Dynamic Characteristics Stability Digital I/O Timing I/O General-Purpose Up/Down Counter/Timers Frequency Scaler Triggers Analog Trigger Digital Trigger External Input for Digital or Analog Trigger (PFI0/TRIG1) Page Environmental Safety Electromagnetic Compatibility CE Compliance Page Figure B-1. 68-Pin Connector Pin Assignment for the NI PCI-611 0/6111 Figure B-2. 50-Pin Connector Pin Assignment for the NI PCI-611 0/6111 C Common Questions General Information Installing and Configuring Analog Input and Output Timing and Digital I/O Page Page D Technical Support and Professional Services Page Glossary Numbers/Symbols A B C D E F G H I K L M N O P Page R S T U V W Index Symbols Numerics A B C D E F G H I K L M N O Q R S T U V W