Manuals / Brands / Computer Equipment / Network Card / National Instruments / Computer Equipment / Network Card

National Instruments NI PCI-6110, NI PCI-6111 Table 4-3. I/O Signal Summary for the NI PCI-6110/6111

1 118

Download 118 pages, 1.13 Mb

Chapter 4 Connecting Signals

NI PCI-6110/6111 User Manual 4-6 ni.com

GPCTR0_OUT DGND Output Counter 0 Output—This output is from the

general-purpose counter 0 output.

FREQ_OUT DGND Output Frequency Output—This output is from the frequency

generator output.

Table 4-3. I/O Signal Summary for the NI PCI-6110/6111

Signal Name

Signal

Type and

Direction

Impedance

Input/

Output

Protection

(Volts)

On/Off

Source

(mA at V)

Sink

(mA atV)

Rise

Time

(ns) Bias

ACH<0..3>+ AI 1MΩ

in parallel

with

100pF1

1MΩ

in parallel

with

10pF2

42 V — — — —

ACH<0..3>– AI 10nF 42 V — — — ±200 pA

ACH<0..3>GND AI — — — — — —

DAC0OUT AO 50ΩShort-circuit

to ground

5 at 10 5 at –10 300

V/µs

—

DAC1OUT AO 50ΩShort-circuit

to ground

5 at 10 5 at –10 300

V/µs

—

AOGND AO — — — — — —

DGND DO — — — — — —

VCC DO 0.1ΩShort-circuit

to ground

1 A — — —

DIO<0..7> DIO — Vcc +0.5 13 at (Vcc –0.4) 24 at0.4 1.1 50kΩ pu

SCANCLK DO — — 3.5 at (Vcc –0.4) 5 at 0.4 1.5 50 kΩ pu

EXTSTROBE* DO — — 3.5 at (Vcc –0.4) 5 at 0.4 1.5 50 kΩ pu

PFI0/TRIG1 AI/DIO 10kΩ±35 Vcc +0.5 3.5 at (Vcc –0.4) 5 at 0.4 1.5 9kΩ pu

and

10kΩ pd

PFI1/TRIG2 DIO — Vcc +0.5 3.5 at (Vcc –0.4) 5 at 0.4 1.5 50 kΩ pu

PFI2/CONVERT* DIO — Vcc +0.5 3.5 at (Vcc –0.4) 5 at 0.4 1.5 50 kΩ pu

Table 4-2. Signal Descriptions for I/O Connector Pins (Continued)

Signal Name Reference Direction Description

Contents

Main Page Important Information Warranty Copyright Trademarks Patents Compliance FCC/Canada Radio Frequency Interference Compliance Determining FCC Class FCC/DOC Warnings Class A Contents Chapter 4 Connecting Signals Page About This Manual Conventions National Instruments Documentation Related Documentation Introduction About the NI PCI-6110/6111 What You Need to Get Started Software Programming Choices NI-DAQ National Instruments ADE Software Optional Equipment Custom Cabling Unpacking Safety Information Page Page Installing and Configuring the NI PCI-6110/6111 Installing the Software Installing the Hardware Configuring the Device National Instruments Corporation 3-1 NI PCI-6110/6111 User Manual Hardware Overview DAQ - STC RTSI Bus Figure 3-1. NI PCI-6110 Block Diagram I/O Connector Analog Input Input Mode Note The inputs are differential only in the sense that the ground loops are broken. The I/O Connector RTSI Bus Input Polarity and Input Range Considerations for Selecting Input Ranges Input Coupling Analog Output Analog Trigger Figure 3-3. Analog Trigger Block Diagram for the NI PCI-6110 Figure 3-4. Analog Trigger Block Diagram for the NI PCI-6111 Page Page Digital I/O Timing Signal Routing Page Programmable Function Inputs Device and RTSI Clocks RTSI Triggers Connecting Signals I/O Connector Figure 4-1. 68-Pin I/O Connector Pin Assignment for the NI PCI-6110/6111 Figure 4-2. 50-Pin Connector Pin Assignments for the NI PCI-61 10/6111 I/O Connector Signal Descriptions Table 4-2. Signal Descriptions for I/O Connector Pins Page Page Table 4-3. I/O Signal Summary for the NI PCI-6110/6111 Table 4-3. I/O Signal Summary for the NI PCI-6110/6111 (Continued) Connecting Analog Input Signals Types of Signal Sources Floating Signal Sources Ground-Referenced Signal Sources Differential Measurements Differential Connection Considerations Differential Connections for Ground-Referenced Signal Sources Figure 4-4. Differential Input Connections for G round-Referenced Signals Differential Connections for Nonreferenced or Floating Signal Sources Common-Mode Signal Rejection Considerations Working Voltage Range Analog Output Signal Connections Digital I/O Signal Connections Power Connections Timing Connections Programmable Function Input Connections DAQ Timing Connections TRIG1 Signal TRIG2 Signal Page STARTSCAN Signal Page CONVERT* Signal AIGATE Signal SISOURCE Signal SCANCLK Signal EXTSTROBE* Signal Waveform Generation Timing Connections WFTRIG Signal UPDATE* Signal UISOURCE Signal General-Purpose Timing Signal Connections GPCTR0_SOURCE Signal GPCTR0_GATE Signal GPCTR0_OUT Signal GPCTR0_UP_DOWN Signal GPCTR1_SOURCE Signal GPCTR1_GATE Signal GPCTR1_OUT Signal GPCTR1_UP_DOWN Signal Page FREQ_OUT Signal Field Wiring Considerations Page Calibration Loading Calibration Constants Self-Calibration External Calibration A Specifications Analog Input Input Characteristics Accuracy Information Transfer Characteristics Amplifier Characteristics Dynamic Characteristics Stability Analog Output Output Characteristics Transfer Characteristics Voltage Output Dynamic Characteristics Stability Digital I/O Timing I/O General-Purpose Up/Down Counter/Timers Frequency Scaler Triggers Analog Trigger Digital Trigger External Input for Digital or Analog Trigger (PFI0/TRIG1) Page Environmental Safety Electromagnetic Compatibility CE Compliance Page Figure B-1. 68-Pin Connector Pin Assignment for the NI PCI-611 0/6111 Figure B-2. 50-Pin Connector Pin Assignment for the NI PCI-611 0/6111 C Common Questions General Information Installing and Configuring Analog Input and Output Timing and Digital I/O Page Page D Technical Support and Professional Services Page Glossary Numbers/Symbols A B C D E F G H I K L M N O P Page R S T U V W Index Symbols Numerics A B C D E F G H I K L M N O Q R S T U V W