8. Appendix

￿Troubleshooting

This section helps you resolve problems you may encounter while setting up or using the projector.

Indicator MessagesPower Indicator

 

Indicator Condition

 

Projector ConditionNote

 

Off

 

The main power is off

 

 

 

 

 

 

 

Blinking light

Green

 

0.5 sec On,

The projector is getting ready to turn on.

Wait for a moment.

 

 

 

0.5 sec Off

 

 

 

 

 

 

2.5 sec On,

Off Timer is activated.

 

 

 

0.5 sec Off

 

 

 

 

 

 

 

 

 

 

Orange

 

0.5 sec On,

The projector is cooling down.

Wait for a moment.

 

 

 

0.5 sec Off

 

 

 

 

 

 

 

 

 

 

Steady light

Green

 

The projector is turned on.

 

Orange

 

The projector is in Standby.

 

 

 

 

 

 

 

Status Indicator

 

 

 

 

 

 

 

 

 

 

 

 

Indicator Condition

 

Projector Condition

Note

 

Off

 

Normal

 

 

 

 

 

 

 

Blinking light

Red

 

1 cycle (0.5 sec On,

Lamp cover error

Replace the lamp cover correctly.

 

 

 

2.5 sec Off)

 

(page 105)

 

 

 

2 cycle (0.5 sec On,

Temperature error

The projector is overheated. Move

 

 

 

0.5 sec Of)

 

the projector to a cooler location.

 

 

 

3 cycle (0.5 sec On,

Power error

Power unit will not work correctly.

 

 

 

0.5 sec Off)

 

 

 

 

 

 

4 cycle (0.5 sec On,

Fan error

Fans will not work correctly.

 

 

 

0.5 sec Off)

 

 

 

 

 

 

6 cycle (0.5 sec On,

Lamp error

Lamp fails to light. Wait a full

 

 

 

0.5 sec Off)

 

minute and then turn on again.

 

Green

 

Re-firing the lamp

The projector is re-firing.

 

 

 

 

 

 

 

Orange

 

1 cycle(0.5 sec On,

Network conflict

Both the built-in LAN and the wireless

 

 

 

2.5 sec Off)

 

LAN cannot be connected to the same

 

 

 

 

 

network at the same time.

 

 

 

 

 

To use both built-in LAN and wireless

 

 

 

 

 

LAN at the same time, connect them to

 

 

 

 

 

different networks. (page 87)

Steady light

Orange

 

Control Panel Lock is on

You have pressed cabinet button

 

 

 

 

 

when Control Panel Lock is on.

 

 

 

 

 

(page 79)

 

 

 

 

 

 

Green

 

The projector is in Standby.

 

 

 

 

 

 

 

Lamp Indicator

 

 

 

 

 

 

 

 

 

 

 

 

Indicator Condition

 

Projector Condition

Note

 

Off

 

Normal

 

 

 

 

 

 

 

Blinking light

Red

 

Lamp has reached its end of life. Lamp

Replace the lamp.

 

 

 

 

replacement message will be displayed.

(page 104)

Steady light

Red

 

Lamp has been used beyond its limit. The

Replace the lamp.

 

 

 

 

projector will not turn on until the lamp is

(page 104)

 

 

 

 

replaced.

 

 

 

Green

 

Lamp is in Eco mode

 

 

 

 

 

 

 

107