8. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
| Indicator Condition |
| Projector Condition | Note | |
|
| Off |
| The main power is off. | – |
|
|
| 0.5 sec On, | The projector is getting ready to turn on. | Wait for a moment. |
|
|
| 0.5 sec Off | ||
|
| Green |
|
| |
|
| 2.5 sec On, | Off Timer (Off Time) is activated. | – | |
|
|
| |||
|
|
| 0.5 sec Off | ||
Blinking light |
|
|
|
| |
|
| 0.5 sec On, | The projector is cooling down. | Wait for a moment. | |
|
|
| |||
|
|
| 0.5 sec Off | ||
|
| Orange |
|
| |
|
| 2.5 sec On, | The Program Timer is activated. | – | |
|
|
| |||
|
|
| 0.5 sec Off | ||
|
|
|
|
| |
Steady light |
| Green |
| The projector is turned on. | – |
| Orange |
| The projector is in Standby. | – | |
|
|
| |||
Status Indicator |
|
|
| ||
| Indicator Condition |
| Projector Condition | Note | |
|
| Off |
| Normal | – |
|
|
| 1 cycle (0.5 sec | Lamp cover error | Reattach the lamp cover correctly. |
|
|
| On, 2.5 sec Off) | ||
|
|
| 2 cycle (0.5 sec | Temperature error | The projector is overheated. Move |
|
| Red | On, 0.5 sec Of) |
| the projector to a cooler location. |
Blinking light |
| 4 cycle (0.5 sec | Fan error | Fans will not work correctly. | |
|
| ||||
|
|
| On, 0.5 sec Off) | ||
|
|
| 6 cycle (0.5 sec | Lamp error | Lamp fails to light. Wait a full min- |
|
|
| On, 0.5 sec Off) | ute and then turn on again. | |
|
| Green |
| The projector is | |
|
|
|
|
| You have pressed cabinet button |
|
|
|
| Control Panel Lock is on | when Control Panel Lock is on. |
Steady light |
| Orange |
|
| |
|
|
| CONTROL ID error | Remote control ID and projector ID | |
|
|
|
| ||
|
|
|
| are not matched. | |
|
|
|
|
| |
|
| Green |
| The projector is in Standby. | – |
Lamp Indicator |
|
|
| ||
| Indicator Condition | Projector Condition | Note | |
|
| Off | Normal | – |
Blinking light |
| Red | Lamp has reached its end of life. Lamp replace- | Replace the lamp. |
| ment message will be displayed. | |||
|
|
| ||
|
| Red | Lamp has been used beyond its limit. The projec- | Replace the lamp. |
Steady light |
| tor will not turn on until the lamp is replaced. | ||
|
| |||
|
| Green | Lamp is in Eco mode | – |
If the temperature inside the projector rises too high, the
Should this happen, do the following:
•Unplug the power cable after the cooling fans stop.
•Move the projector to a cooler location if the room where you are presenting is particularly too warm.
•Clean the ventilation holes if they are clogged with dust.
•Wait about 60 minutes until the inside of the projector becomes cool enough.
120