Manuals / NEC / Computer Equipment / Projector

NEC XT9000 user manual REMOTE 1 Connector, Pin No, Function

Models: XT9000

1 54

Page 27

REMOTE 1 Connector

5		4	3	2	1
10		9	8	7	6
15	14		13	12	11

This connector is used for either connecting the ISS-6020/ISS-6020G Switcher or a third party external control device (Contact Closure). When the Switcher is used, connect it with the optional control cable (15-15 pin; 50 ft./16m; CTL-6010) to this connector.

When used with the Switcher.

Pin No.	FUNCTION

1, 2, 6 and 7	Sending and receiving data when the Switcher is used.

9	Identifying the Projector

15	Ground

3, 8,11 and 12	Used inside the Projector. Normally set to OPEN.

When using with the Switcher ISS-6020/ISS-6020G, connect No. 1,2,6,7,9 and15 pins of the projector to the same No. pins of the switcher as shown below.

Pin Configuration of Optional CTL-6010 Cable

REMOTE 1 connector of the Projector mini D-sub 15 pin (female)

REMOTE 1 connector of the Switcher mini D- sub 15 pin (female)

Shield (frame ground)

Pins without a number are open.

E – 20

Page 27

Image 27

NEC XT9000 user manual REMOTE 1 Connector, Pin No, Function

Contents

User’s Manual Bedienungshandbuch XT9000User’s Manual XT9000High Light Output Projection System AVERTISSEMENT DOC compliance NoticeDOC avis de conformation 3. GSGV Acoustic Noise Information OrdinancePower Supply Important SafeguardsInstallation To Dealer or InstallerAlimentation Recommandations importantesInstallation A l’attention du revendeur ou de l’installateurHOW YOU CAN GET WARRANTY SERVICE LIMITED WARRANTY USA and Canada onlyHOW LONG IS THE WARRANTY WHAT IS COVERED AND WHAT IS NOT COVEREDTABLE OF CONTENTS Whats In The Box? INTRODUCTIONIntroduction to the XT9000 Projector Getting Started1. Part Names and Functions Press to the OFF position 0 to turn the main power offConnect the supplied power cable here AC Remote sensor ControlsFor the optional XT SDI board Terminal Panel1. INPUT 3 RGB Connector Mini D-Sub 15 pin NOTE This projector is compatible with the ISS-6020 SwitcherNOTE This terminal accepts component signals only NOTE The Pixel Phase is not available Remote ControlNOTE This is also considered the LENS SHUTTER Remote Control PrecautionsRemote Control Battery Installation When using the remote control wirelesslyThrow Distance 2. INSTALLATIONSetting Up Your Projector NOTE The lens must be installed by service personnel onlyCeiling/ Front Lens Shift Adjustable RangeMaximum Possible Range for TL-1ZH, TL-2Z and TL-4Z Fixed Lens TL-08SFSelecting A Location Moving The ProjectorPOWER 3. SETUPConnecting the Power Cable and Turning on the Projector OFF POWERDesktop front, ceiling rear, desktop rear, and ceiling front Set up the projector4. Adjust the image position and the image size 1. Turn on the projector 2. Select your type of projection2 Hookup Setting up for Double Stacking in Link ModeKeystone 1 Stacking the ProjectorsNOTE Use a different single color for each projector 6 Link Mode SettingNOTE In the Link mode the Lens Memory feature is not available 4 Display the internal crosshatch test patternDesktop Rear Projection Projector OrientationCeiling Front Projection Ceiling Rear ProjectionConnecting Your Document Camera When used in standalone operation4. CONNECTIONS Connecting Your PC Or Macintosh ComputerFor more details, contact your dealer When Used with One Switcher ISS-6020/ISS-6020GFor more details, contact your dealer When Used with Two or More Switchers 100 InputsHow to make connections Set the DIP switch S8601 of the SwitcherMaster Setting of S8601ISS-6020 Output toREMOTE 1 Connector Pin NoFUNCTION FUNCTION When used in stand alone operationPin No SHORT/OPENOperating Multiple Projectors with the Remote Control Connection for Double Stacking in Link Mode Using the RGB DIGITAL connectorsConnecting a PC with the RGB digital connector Specify the DVI-D type when you buy DVI cableOne input is switched to another 5. OPERATIONUsing The Menus 3. Adjust The ImageNOTE This feature is available for SW 2 Level mode only A List of Direct Key Combinationsslot without displaying the Select Slot window Menu Tree When Switcher Control is turned onStand alone Preset Time Off Menu windows or dialog boxes typically have the following elements Menu ElementsNOTE Existing direct key settings are overwritten with new settings Menu Descriptions & Functions Source SelectWhen using with a single Switcher ISS-6020 When using with two or more Switcher ISS-6020Image Adjust SourceWhite Balance PictureAspect Ratio not available for RGB Horizontal/Vertical Position when Auto Adjust is offResolution when Auto Adjust is off Video AdjOption Adj NOTE When connecting with a scan converterRef Adj Lens MemoryKeystone turns to the factory preset Factory DefaultProjector Options TimerMenu Mode Sleep TimerDate, Time Preset MenuSignal Select VIDEO 1/2, S-VIDEO1/2 and Switcher SetupNOTE These S-Video signals are not used in the US Signal Select RGB1/2Link Mode Switcher ControlNOTE In the Link mode the Lens Memory feature is not available Default Source SelectSource Information PC Card FilesHelp ContentsLink Mode Test Pattern6. SPECIFICATIONS OpticalElectrical Addressable Remote Control wired / wireless Mechanical26.8 W x 38.3 D x 14.2 H with foot not including lens hood and handle 7. Optional Accessories REMOTE 3 XLR Pin Assignments and SignalsOUTIN 8. Compatible Input Signal List Compatible Input Signal ListNOTE 2 UXGA can be supported for separate sync signal only Master projector 9. List of Menu Items Available on Link ModeFunction Link modeDimensions AppendixThe drawings do not include the lens part NOTE 2 The Lens Memory function is not available in the Link mode Tips on Adjusting Focus for Lens Memory FunctionAdjusting the Focus Preparation Recommend

REMOTE 1 Connector

Pin No.

FUNCTION