![](/images/new-backgrounds/1186273/18627333x1.webp)
NTI VEEMUX VIDEO MATRIX SWITCH
ETHERNET CONTROL
Telnet Interface
The Telnet Interface enables the user to control the switch using telnet client through an Ethernet connection. The telnet server listens on port 2000. To access the telnet interface, using the current IP address type the following in a command shell:
telnet 192.168.1.30 2000
The VEEMUX will prompt the user for a password. The user must enter the password followed by <Enter>.
The factory default password is "admin".
With a proper password sent the VEEMUX will respond with:
Password Successful
Connection Established
The following commands are now available:
| Command |
| Reply |
| Description |
|
|
|
|
|
|
| H(elp) or |
| Displays the list of |
| Help |
| h(elp) |
| commands |
| |
|
|
|
| ||
|
|
| User is prompted to |
|
|
| CP |
| introduce the password |
| Change password |
|
|
| twice |
|
|
| CS nn,mm |
| *<CR> |
| Connect One Output (User Port) To Input (Video source) |
|
|
|
|
|
|
| CA nn |
| *<CR> |
| Connect All Outputs To Input |
|
|
|
|
|
|
| RO nn |
| *<CR>mm<CR> |
| Read Connection For Output. |
|
|
| Returns the number of the input (mm) connected to output nn | ||
|
|
|
|
| |
| CC nn |
| *<CR>nn<CR> |
| Save Matrix Connections Into Memory Bank nn |
|
|
| nn should be between 00 and 99 | ||
|
|
|
|
| |
| RC nn |
| *<CR>nn<CR> |
| Restore Matrix Connections From Memory Bank nn |
|
|
| nn should be between 00 and 99 | ||
|
|
|
|
| |
| CB nn |
| *<CR> |
| Change baud rate of serial line, nn=12(00),24(00),48(00),96(00) |
|
|
| Factory default is 9,600. | ||
|
|
|
|
| |
| RS |
| *<CR> | Reset Unit | |
|
|
|
|
| |
| RV 00 |
| *<CR>string\0<CR> | Read NTI Version String | |
|
|
|
|
|
|
| RU |
| *<CR>nn,mm<CR> |
| Read Unit Size |
|
|
| Returns the number of inputs(nn) and the number of outputs (mm) | ||
|
|
|
|
| |
| Ss nn,dwt | *<CR> |
| Set value of Scan Mode dwell time (see pg. 8) for specific Output (nn) | |
|
| dwt = | |||
|
|
|
|
| |
| Gs nn |
| *<CR> |
| Read set Scan Mode dwell time value (dwt) for specific Output (nn) in |
|
| dwt<CR> |
| seconds (see also "Scan Mode" on page 8) | |
|
|
|
| ||
| Sa nn,mm |
| *<CR> |
| Set scan list of individual output nn to all inputs mm |
|
|
|
|
|
|
| Sc nn |
| *<CR> |
| Clear scan list of individual output nn |
|
|
|
|
| |
| S+ nn,mm | *<CR> |
| Add input mm to Scan List of output nn | |
|
|
|
|
|
|
| S- nn,mm |
| *<CR> |
| Remove input mm from Scan List of output nn |
|
|
|
|
|
|
| Sx nn |
| *<CR>oooxoxxxooooxxx< |
| Display the Scan List of output nn (o=skip x=don't skip) |
|
| CR> |
| ||
|
|
|
|
| |
|
| Good Bye. |
| Quit telnet session | |
| (see note 4 below) |
| Connection to host lost. |
| |
|
|
|
|
13