New Buck Corporation 34 manual Gas Pressure Check

GAS PRESSURE CHECK

Check the inlet pressure to the burner to ensure that it is as shown in the table below.

NOTE: The pressure check pointGASis PRESSURElocated on the rightCHECKside of the valve facing burner, for SIT Millivolt, and the left side for SIT Modulating.

The appliance and its appliance main gas valve must be disconnected from the gas supply Check the inlet pressure to the burner to ensure that it is as shown in the table below.

piping system during any pressure testing of that system at test pressures in excess of 1/2 psi NOTE: The pressure check point is located on the right side of the valve facing burner, for ITT, (3.5kPa).

and the left side for SIT.

The appliance must be isolated from the gas supply piping system by closing its equipment The appliance and its appliance main gas valve must be disconnected from the gas supply shut-off valve during any pressure testing of the gas supply piping system at test pressures equal piping system during any pressure testing of that system at test pressures in excess of 1/2 psi to or less than 1/2 psi (3.5 kPa).

(3.5kPa).

The appliance must be isolated from the gas supply piping system by closing its equipment
VALVE	(MILLIVOLT)		(SIT MANUAL-MODULATING)
shut-off valve during any pressure testing of the gas supply piping system at test pressures equal
MODEL:	FP34	FP34	FP34		FP34
to or less than 1/2 psi (3.5 kPa).		Propane	Natural		Propane
GAS	Natural
Maximum Heat Input	33,000	33,000	33,000		33,000
MODEL	FP34	23,000	FP34		13,000
Minimum Heat Input	23,000		12,000
Gas	Natural		Propane
Gas Inlet Pressure	33000		33000
Maximum Heat Input		13ins.W.C.		9.0ins.W.C.
Maximum	10.5ins.W.C.		10.5ins.W.C.
Gas Inlet Pressure:	* 5.0ins.W.C.	*11ins.W.C.	*5.0ins.W.C.	*11ins.W.C.
Minimum
Maximum	10.5 ins. W.C.		13 ins. W.C.
Manifold Pressure	* 5 ins. W.C.		*11 ins. W.C.
Minimum
Maximum	3.5ins.W.C.	9.0ins.W.C.	3.5ins.W.C.		9.0ins.W.C.
Manifold Pressure	3.5 ins. W.C.		9 ins. W.C.
Minimum	3.0ins.W.C.	8.2ins.W.C.	2.8ins.W.C.		7.2ins.W.C.

NOTE: On initial installation it may be necessary to bleed out air in the gas lines. Do this by

NOTE: On initial installation it may be necessary to bleed out air in the gas lines. Do this by holding the control knob and turning the knob to the “PILOT” position for about 30 seconds. holding the control knob and turning the knob to the “PILOT” position for about 30 seconds. To check the regulator pressure, remove the pressure tag plug at the left side of the regulator To check the regulator pressure, remove the pressure tag plug at the left side of the regulator facing the heater. The pressure should be checked with the heater burning and the control set facing the heater. The pressure should be checked with the heater burning and the control set on high. After measuring the pressure, replace the pressure tap plug, ensuring that there are no on high. After measuring the pressure, replace the pressure tap plug, ensuring that there are no leaks.

leaks.

* For the purpose of minimum input adjustment. * For the purpose of minimum input adjustment.

Solid fuels shall not be burned in the same fireplace where an unvented room heater has Solid fuels shall not be burned in the same fireplace where an unvented room heater has been installed.

been installed.

NOTE: The following label has been provided with this appliance and must be read and

NOTE: The following label has been provided with this appliance and must be read and then attached to the floor of the fireplace or firebox area beneath the appliance. then attached to the floor of the fireplace or firebox area beneath the appliance. The label is a peel and stick label. Make sure the area is cleaned before attaching The label is a peel and stick label. Make sure the area is cleaned before attaching the label to it.

the label to it.

10