Manuals / New Buck Corporation / Household Appliance / Indoor Fireplace

New Buck Corporation DV23ZC manual Installation, VERTICAL TERMINATION continued

Models: DV23ZC

1 33

Download 33 pages 10.86 Kb

Page 18

Image 18

Use only 45 degree elbows. Use of 90 degree elbows is not allowed in vertical terminations. The 45 degree elbows offer less restriction to the flow of flue gases and intake air.

INSTALLATION

VERTICAL TERMINATION (continued)

NOTES:

Use only 45 degree elbows. Use of 90 degree elbows is not allowed in vertical terminations. The 45 degree elbows offer less restriction to the flow of flue gases and intake air.

For multi-story vertical installations, a Ceiling Firestop, (Simpson-Dura-Vent, Part 963) is required at the second floor, and any subsequent floors (Figure 14). The opening should be framed to 10" x 10" inside dimensions, in the same manner as shown in Figure 11.

Figure 14

Any occupied areas above the first floor, including closets and storage spaces, which the vertical vent passes through, must be enclosed. The enclosure may be framed and sheet rocked with standard construction materials. However, consult the vent manufacturer’s installation instructions for the minimum allowable clearance between the outside of the vent pipe and the combustible surfaces of the enclosure. Do not fill any of the required air spaces with insulation.

Page 18

Image 18

New Buck Corporation DV23ZC manual Installation, VERTICAL TERMINATION continued

Contents

APPROVED FOR MOBILE HOME INSTALLATION Page TABLE OF CONTENTS Page INTRODUCTION Provide adequate clearances around air openings and adequate accessibility clearance for service and proper operation. Never obstruct the front openings of the appliance GENERAL INFORMATION ASSEMBLY STEPS-OVERVIEWLOCATION AND CLEARANCE INSTALLATION INTERIOR HORIZONTAL MINIMUM INSTALLATIONINSTALLATION WITH INTERIOR VERTICALINSTALLATION GENERAL INFORMATIONINSTALLATION EXTERIOR VENT LOCATIONS and RESTRICTIONSVENTING MUST BE TERMINATED WITHIN SHADED AREA INSTALLATIONMINIMUM - MAXIMUM VENT REQUIREMENTS MINIMUM DISTANCE FROM BEND OF 45 ELBOW TO FACE OF VENT CAPINSTALLATION VENT ASSEMBLYHORIZONTAL TERMINATION INSTALLATION HORIZONTAL TERMINATION continuedConnecting Vent Cap with Horizontal Vent Pipe INSTALLATIONInstalling Vinyl Siding Standoff HORIZONTAL TERMINATION continuedINSTALLATION VERTICAL TERMINATIONINSTALLATION VERTICAL TERMINATION continuedINSTALLATION VERTICAL TERMINATION continued‹ Use only 45 degree elbows. Use of 90 degree elbows is not allowed in vertical terminations. The 45 degree elbows offer less restriction to the flow of flue gases and intake air 600m INSTALLATIONALTITUDE 900mINSTALLATION GAS VALVE CONNECTIONGAS PRESSURE CHECKS OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGOPERATION LIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVECONTROL KNOB NOTE Pilot is located between the first and second burnerPage Page OPERATION GLASS DOOR INSTALLATIONclean the glass when hot PILOT AND FLAMEOPTIONAL ROOM AIR BLOWER WIRING DIAGRAM PILOT ACCESSORIES OR OPTIONSREMOTE CONTROL EYE ROCKER SWITCH PIEZO VALVEMAINTENANCE GENERAL MAINTENANCEThe flow of combustion and ventilation air should not be obstructed KEY# REPLACEMENT PARTSSERVICING PART DESCRIPTIONREPLACEMENT PARTS ADDITIONAL REPLACEMENT PARTS PART DESCRIPTIONPART NUMBER PROCEDURE WARRANTYWARRANTY CONDITIONS AND EXCLUSIONSOTHER RIGHTS

Use only 45 degree elbows. Use of 90 degree elbows is not allowed in vertical terminations. The 45 degree elbows offer less restriction to the flow of flue gases and intake air.

Use only 45 degree elbows. Use of 90 degree elbows is not allowed in vertical terminations. The 45 degree elbows offer less restriction to the flow of flue gases and intake air.