Manuals / Norton Abrasives / Power Tools / Saw

Norton Abrasives Power Plant BBC157-207 Electric, NOTE The Thermal Reset Button Is Located On

Models: BBC207

1 36

Page 27

Power Plant (BBC157-207) Electric

Item No	Description
M1	Motor Assembly w/Switch 1-1/2HP 115/230v/60/1
	Motor Assembly w/Switch 2 HP 115/230v/60/1
M2	Capacitor Box Large (Terminal Box)
M3	Voltage Change Switch
M4	Switch Box Rear
M5	Switch On/Off
M6	Switch Box Cover
M7	Capacitor Box Small
-NA-	Thermal Reset Button 1-1/2 HP
	Thermal Reset Button 2 HP
	NOTE: The Thermal Reset Button Is Located On
	The Rear Of The Large Capacitor Housing
-NA-	Pulley 68MM OD 24MMB 1G Electric Models
	Only
-NA-	Belt XPZ 1500 LW (1) Electric Models Only

Part Number

232084

232085

232085A

231085

231087

231089

231088

231091

83747

72926

Page 27

Image 27

Norton Abrasives BBC547, BBC207 owner manual Power Plant BBC157-207 Electric, NOTE The Thermal Reset Button Is Located On

Contents

COMPACT MASONRY SAW MODELS BBC157 BBC207 BBC547 OWNERS MANUALMODEL SERIAL NO PURCHASE FROM ADDRESS CITY STATE ZIP TELEPHONE NO WARRANTYOWNERS MANUAL III. MaintenanceIV. Parts List Section BBC 157/207/547DO NOT LIFT THE SAW BY THE HANDLE BARS A. Safety PrecautionsI. PREPARATION Important! The following safety precautions must always be observedDust and Silica Warning You Are Responsible For Your Safety I. PREPARATION B. AssemblyDo not install the blade until it is time to use the saw The Norton Company is not responsible for any freight-related damagesFigure 1 Head Locking Screw Removal Figure 2 Head Locking Handle InstallationFigure 3 Depth Limiting Bolt Assembly Depth Limiting BoltFigure 4 Plastic Knob Attachment Figure 5 Leg Attachment Leg AssemblyConveyor Cart Assembly Guide-A-Cut AssemblyFigure 6 Back Stop Assembly Figure 7 Conveyor Cart Installation Water Curtain Assembly Water Curtain AssemblyWrenches Water Pump Assembly The Water Pump requires no additional assemblyFigure 10 Wrench Placement I. PREPARATION C. BBC157/207/547 Series Masonry Saw SpecificationsDimensions/Weight CharacteristicsI. PREPARATION Saws are wired for 115 Volt from the factoryD. Electrical Connections GeneratorsD. Wiring Diagram Electrical Connections 115 Volt 230 Volt5711 R.S. Boreham, Jr. St. P.O. Box Fort Smith, AR Phone 501 Fax 501 Tel 800 426-7701 Fax 678 F. Gasoline EngineHonda Power Equipment Group 4900 Marconi Dr Alpharetta, GA I. PREPARATIONA. Installing the Blade II. OPERATIONUse Only Norton Clipper Diamond Blades II. OPERATION B. How To Use Step Cutting With Abrasive BladesII. OPERATION b. Make one or two cuts in a soft brick or light weight blockD. How To Use Blockbuster Compact For Dry Cutting E. How To Use Blockbuster Compact For Wet CuttingII. OPERATION A. V-Belts III. MAINTENANCEIII. MAINTENANCE B. MotorC. Engine D. Blade Shaft BearingsLUBRICATION OF SEALMASTER BEARINGS E. PumpA. Ordering Information V. PARTS LIST SECTIONB. Parts List C. Power Unit Service InformationV. PARTS LIST SECTION Power Plant BBC547 Gasoline1 Honda motor GX160 2 Motor pulley 3 Belt XPZ 562 LW Power Plant BBC547 GasolinePower Plant BBC157-207 Electric NOTE The Thermal Reset Button Is Located OnThe Rear Of The Large Capacitor Housing Frame Common All BBC157-207-547 Part Number Frame Common All BBC157-207-547Item No DescriptionCutting Head Common All BBC157-207-547 Locking Handle for cutting head was Cutting Head Common All BBC157-207-547Cutting Table Common All BBC157-207-547 Part Number Cutting Table Common All BBC157-207-547Item No DescriptionC. Baldor Service Policy D. Honda Service Policy Phone 800-554-8009 or Fax 800-443-1092 or SOLD AND SERVICED BYSaint-Gobain Abrasives, Inc Norton Construction Products 2770 West Washington Street Stephenville, TX

Power Plant (BBC157-207) Electric

NOTE: The Thermal Reset Button Is Located On

The Rear Of The Large Capacitor Housing