Manuals / Norton Abrasives / Power Tools / Saw

Norton Abrasives Cutting Table Common All BBC157-207-547, Item No, Description, Part Number

Models: BBC207

1 36

Page 33

Cutting Table (Common All BBC157-207-547)

Item No	Description	Part Number
56	Conveyor Cart (aka Cutting Table) Complete	83754
	With Wheels, Top, Back Stop, and Conveyor Cart
	Stop
57	Top For Cutting Table (Wood & Rubber)	76742
	w/Hardware
	Screw 4x 12mm DIN 7976 (sold each, 11	30373
	required)
58	Conveyor Cart Frame Only (No Wheels, Top,	-NA- Part of 83754
	Backstop or Conveyor Cart Stop)
59	Wheel Kit, Conveyor Cart (Set Of 4) w/Hardware	75333
	Carriage Bolt M10 x 30 DIN 603 (sold each, 3	27282
	required)
	Washer 10.5 DIN 9021 (sold each, 3 required)	27508
	Wing Nut M10 DIN 315 (sold each, 3 required)	27040
60	Back Stop Plate	83752
61	Scale for Conveyor Cart w/rivets	83753
62	Stop Assembly for Conveyor Cart (Complete)	82856
	Rubber Stop	-NA- Part of 82856
	Nut M6 DIN 439	27003
	Washer M6 DIN 125	27539

Item No	Description	Part Number
-NA-	Guide-A-Cut Assembly	83892

Page 33

Image 33

Norton Abrasives BBC547, BBC207 owner manual Cutting Table Common All BBC157-207-547, Item No, Description, Part Number

Contents

COMPACT MASONRY SAW MODELS BBC157 BBC207 BBC547 OWNERS MANUALMODEL SERIAL NO PURCHASE FROM ADDRESS CITY STATE ZIP TELEPHONE NO WARRANTYIV. Parts List Section III. MaintenanceBBC 157/207/547 OWNERS MANUALI. PREPARATION A. Safety PrecautionsImportant! The following safety precautions must always be observed DO NOT LIFT THE SAW BY THE HANDLE BARSDust and Silica Warning You Are Responsible For Your Safety Do not install the blade until it is time to use the saw B. AssemblyThe Norton Company is not responsible for any freight-related damages I. PREPARATIONFigure 3 Depth Limiting Bolt Assembly Figure 2 Head Locking Handle InstallationDepth Limiting Bolt Figure 1 Head Locking Screw RemovalFigure 4 Plastic Knob Attachment Figure 5 Leg Attachment Leg AssemblyConveyor Cart Assembly Guide-A-Cut AssemblyFigure 6 Back Stop Assembly Figure 7 Conveyor Cart Installation Water Curtain Assembly Water Curtain AssemblyWrenches Water Pump Assembly The Water Pump requires no additional assemblyFigure 10 Wrench Placement Dimensions/Weight C. BBC157/207/547 Series Masonry Saw SpecificationsCharacteristics I. PREPARATIOND. Electrical Connections Saws are wired for 115 Volt from the factoryGenerators I. PREPARATIOND. Wiring Diagram Electrical Connections 115 Volt 230 Volt5711 R.S. Boreham, Jr. St. P.O. Box Fort Smith, AR Phone 501 Fax 501 Honda Power Equipment Group 4900 Marconi Dr Alpharetta, GA F. Gasoline EngineI. PREPARATION Tel 800 426-7701 Fax 678A. Installing the Blade II. OPERATIONUse Only Norton Clipper Diamond Blades II. OPERATION B. How To Use Step Cutting With Abrasive BladesII. OPERATION b. Make one or two cuts in a soft brick or light weight blockD. How To Use Blockbuster Compact For Dry Cutting E. How To Use Blockbuster Compact For Wet CuttingII. OPERATION A. V-Belts III. MAINTENANCEC. Engine B. MotorD. Blade Shaft Bearings III. MAINTENANCELUBRICATION OF SEALMASTER BEARINGS E. PumpB. Parts List V. PARTS LIST SECTIONC. Power Unit Service Information A. Ordering InformationV. PARTS LIST SECTION Power Plant BBC547 Gasoline1 Honda motor GX160 2 Motor pulley 3 Belt XPZ 562 LW Power Plant BBC547 GasolinePower Plant BBC157-207 Electric NOTE The Thermal Reset Button Is Located OnThe Rear Of The Large Capacitor Housing Frame Common All BBC157-207-547 Item No Frame Common All BBC157-207-547Description Part NumberCutting Head Common All BBC157-207-547 Locking Handle for cutting head was Cutting Head Common All BBC157-207-547Cutting Table Common All BBC157-207-547 Item No Cutting Table Common All BBC157-207-547Description Part NumberC. Baldor Service Policy D. Honda Service Policy Saint-Gobain Abrasives, Inc Norton Construction Products SOLD AND SERVICED BY2770 West Washington Street Stephenville, TX Phone 800-554-8009 or Fax 800-443-1092 or