Omega OMA-P1104 4.9 Local Voice Mute, 4.10 Voice Repetitions

Omegaphone® OMA-P1104 User’s Manual

40

4.9 Local Voice Mute

When the OMA-P1104 dials out to report an alarm, it also

audibly recites the alarm message at its installation site. The

Local Voice Mute command allows you to turn off the voice at

the OMA-P1104’s site during alarm dialouts and status call-ins.

This feature is used to prevent intruders or unauthorized

persons from hearing the alarm dial-out message or from

hearing the Status Report during an off-site call.

4.9.1 Enable/Disable Local Voice Mute

To enable/disable Local Voice Mute:

1. Press SENSOR ON/OFF.

SENSOR

ON/OFF

2. Press MUTE.

CODE

MUTE

The OMA-P1104 will say “On,” to indicate that Local

Voice Mute is enabled, or“Off,” to indicate that it is

disabled.

3. Repeat key sequence to switch between enabled or

disabled Local Voice Mute.

4.10 Voice Repetitions

The Voice Repetitions feature allows programming of the

number of times the alarm message is delivered per phone call

during alarm dial-out.

The maximum repetitions may be set to 10; the default is

3 repetitions.

Contents

Main Page i IMPORTANT SAFETY INSTRUCTIONS Omegaphone OMA-P1104 Users Manual ii iii FCC Requirements iv v Canadian Department of Communications Statement Page Table of Contents IMPORTANT SAFETY INSTRUCTIONS......................... i Chapter 1: Introduction................................................. 1 Chapter 2: Installation................................................... 3 Chapter 3: Quick Start ................................................15 Chapter 4: Communications Programming.............. 23 Chapter 5: Alarm Programming................................. 49 Page Page Page Chapter 1: Introduction 1 Chapter 1: Introduction Technical Support Chapter 2: Installation 2.1 Operating Environment 2.2 Mounting Page --- --- +++ +++ 2.5 Starting the OMA-P1104 2.6 Run Mode and Standby Mode RUN STANDBY 2.7 Telephone Line 2.8 The Microphone 2.9 Alert Inputs 2.10 Installing the Sensor Page 2.11 Multiple Sensors 2.12 Outdoor Wiring 2.13 Disconnecting the OMA-P1104 for Storage or Seasonal Use. Page Chapter 3: Quick Start 3.1 The Local Keypad 3.2 Preparation for Programming 3.3 Quick-Start Programming Steps Step 1: Set Configuration of Inputs 17 Step 2: Set the ID Number 18 Step 3: Set Dial-Out Telephone Numbers 19 Step 4: Set Temperature Limits Page 3.4 Summary of the Alarm Dial-Out Process Page 23 Chapter 4: Communications Programming 4.1 The Unit ID Number 24 4.1.1 Programming the ID Number 4.1.2 Interrogating the ID Number 25 4.2 Dial-out Telephone Numbers 4.2.1 Programming Dial-out Telephone Numbers 26 4.2.2 Interrogating a Dial-out Telephone Number 4.2.3 Erasing a Telephone Number 3. Press the number key (from 1 to 4) representing the telephone number you want to erase. 28 4.4.1 Special Dialing Keys 29 4.4.2 Incorporating a Pause 30 7. Press ENTER. The OMA-P1104 will say Enter. 4.4.3 Incorporating a Pound (#) or Asterisk (*) Incorporate a pound or asterisk if it is normally included in telephone number: 1. Press SET. SET # 31 4.4.4 Special Dialing to a Beeper or Pager Page 33 4.5 Rings Until Answer 4.5.1 Programming Rings Until Answer 34 4.5.2 Interrogating Rings Until Answer- 4.6 TAD (Telephone Answering Device) 35 4.6.1 TAD Enable/Disable 4.6.2 Using the TAD Feature 36 4.6.3 No TAD In Use 4.7 Listen-in Time 37 4.7.1 Programming the Listen-in Time 38 4.7.2 Interrogating the Listen-in Time 4.8 Call Delay 4.8.1 Programming the Call Delay 39 3. Using the number keys, enter the minutes. The OMA-P1104 recites the digits as they are pressed. The OMA-P1104 will recite the programmed Call Delay. 4. Press ENTER. The OMA-P1104 responds: Enter seconds. 5. Using the number keys, enter the seconds. The OMA- P1104 recites the digits as you press them. 4.9 Local Voice Mute 4.9.1 Enable/Disable Local Voice Mute 4.10 Voice Repetitions 41 4.10.1 Programming Voice Repetitions The OMA-P1104 will recite the number programmed. To program Voice Repetitions: 1. Press SET. SET # 4.11 Intercall Time 4.11.1 Programming Intercall Time 43 4.11.2 Interrogating Intercall Time 4.12 Maximum Number of Calls (Max Calls) 44 4.12.1 Programming Max Calls 45 4.12.2 Interrogating Max Calls 4.13 The Clock 4.13.1 Setting the Clock 46 4.13.2 Interrogating for the Current Time 47 4.14 The Security Code 4.14.1 Locking the Keypad 48 4.14.2 Unlocking the Keypad Chapter 5: Alarm Programming 5.1 Input Configuration 50 5.1.1 Programming Input Configuration STATUS 51 5.1.2 Verifying Input Configuration 5.2 Enable/Disable Inputs 5.2.1 Changing Enabled/Disabled Input Status 52 5.2.2 Verifying Enabled/Disabled Input Status 5.3 Input Recognition Time 53 5.3.1 Programming Input Recognition Time 54 5.3.2 Interrogating Input Recognition Time 5.4 Establishing High and Low Temperature Limits 55 5.4.1 Programming Temperature Limits for a Selected Input 56 5.4.2 Disabling Alarm Response to High or Low Temperature 57 5.4.3 Interrogating High and Low Temperature Limits 5.5 Temperature Scale 58 5.6 Temperature Calibration 5.6.1 Programming Temperature Calibration 59 5.6.2 Interrogating Temperature Calibration 5.7 Obtaining Current Temperature 60 5.8 AC Power Monitoring Enable/Disable 5.8.1 Enabling/Disabling the AC Power Alarm 61 5.9 AC Power Failure Recognition Time 5.9.1 Programming Power Failure Recognition Time 62 2. Press RECOGNITION TIME. 5. Press ENTER. The OMA-P1104 responds: Enter seconds. 7. Press ENTER. The OMA-P1104 responds: OK. ENTER 5.10 Sound Alarm Monitoring 5.10.1 Programming Sound Alarm Sensitivity 64 LISTEN TIME SOUND 5. Press ENTER. The OMA-P1104 responds: Enter. TONE PM 5.10.2 Interrogating Sound Sensitivity 5.11High Sound Alarm Enable/Disable 66 5.11.1Changing Enabled/Disabled High Sound Alarm 5.12 Exit Delay Page Page 69 Chapter 6: Acknowledgment, Status Report, and Remote Access 6.1 Alarm Acknowledgment 6.1.1 Local Acknowledgment 6.1.2 Touch-ToneTM Acknowledgment Page 6.2 Status Report STATUS 72 6.2.1 Example: Status Report, No Alarms 73 6.2.2 Example: Status Report, Existing Alarms 74 6.2.3 Example: Status Report, Disabled Inputs 75 6.2.4 Battery Condition 6.2.5 Remote Access by Touch-Tone Telephone Page Page Page Appendix A: Troubleshooting 80 Cause Solution Communications / Dial-out: Problem Page 82 Problem Solution Communications / Dial-out: Cause Page Page Page Page Appendix B