Omega OMA-P1104 iv

Omegaphone® OMA-P1104 User’s Manual

iv

The telephone company may ask that you disconnect this

equipment from the network until the problem has been

corrected or until you are sure that the equipment is not

malfunctioning.

Part 15: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits a designed to provide reason-

able protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the

receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/television

technician for help.

OMEGAPHONE® is a registered trademark of Omega

Touch Tone™ is a registered trademark of AT&T.

Contents

Main Page i IMPORTANT SAFETY INSTRUCTIONS Omegaphone OMA-P1104 Users Manual ii iii FCC Requirements iv v Canadian Department of Communications Statement Page Table of Contents IMPORTANT SAFETY INSTRUCTIONS......................... i Chapter 1: Introduction................................................. 1 Chapter 2: Installation................................................... 3 Chapter 3: Quick Start ................................................15 Chapter 4: Communications Programming.............. 23 Chapter 5: Alarm Programming................................. 49 Page Page Page Chapter 1: Introduction 1 Chapter 1: Introduction Technical Support Chapter 2: Installation 2.1 Operating Environment 2.2 Mounting Page --- --- +++ +++ 2.5 Starting the OMA-P1104 2.6 Run Mode and Standby Mode RUN STANDBY 2.7 Telephone Line 2.8 The Microphone 2.9 Alert Inputs 2.10 Installing the Sensor Page 2.11 Multiple Sensors 2.12 Outdoor Wiring 2.13 Disconnecting the OMA-P1104 for Storage or Seasonal Use. Page Chapter 3: Quick Start 3.1 The Local Keypad 3.2 Preparation for Programming 3.3 Quick-Start Programming Steps Step 1: Set Configuration of Inputs 17 Step 2: Set the ID Number 18 Step 3: Set Dial-Out Telephone Numbers 19 Step 4: Set Temperature Limits Page 3.4 Summary of the Alarm Dial-Out Process Page 23 Chapter 4: Communications Programming 4.1 The Unit ID Number 24 4.1.1 Programming the ID Number 4.1.2 Interrogating the ID Number 25 4.2 Dial-out Telephone Numbers 4.2.1 Programming Dial-out Telephone Numbers 26 4.2.2 Interrogating a Dial-out Telephone Number 4.2.3 Erasing a Telephone Number 3. Press the number key (from 1 to 4) representing the telephone number you want to erase. 28 4.4.1 Special Dialing Keys 29 4.4.2 Incorporating a Pause 30 7. Press ENTER. The OMA-P1104 will say Enter. 4.4.3 Incorporating a Pound (#) or Asterisk (*) Incorporate a pound or asterisk if it is normally included in telephone number: 1. Press SET. SET # 31 4.4.4 Special Dialing to a Beeper or Pager Page 33 4.5 Rings Until Answer 4.5.1 Programming Rings Until Answer 34 4.5.2 Interrogating Rings Until Answer- 4.6 TAD (Telephone Answering Device) 35 4.6.1 TAD Enable/Disable 4.6.2 Using the TAD Feature 36 4.6.3 No TAD In Use 4.7 Listen-in Time 37 4.7.1 Programming the Listen-in Time 38 4.7.2 Interrogating the Listen-in Time 4.8 Call Delay 4.8.1 Programming the Call Delay 39 3. Using the number keys, enter the minutes. The OMA-P1104 recites the digits as they are pressed. The OMA-P1104 will recite the programmed Call Delay. 4. Press ENTER. The OMA-P1104 responds: Enter seconds. 5. Using the number keys, enter the seconds. The OMA- P1104 recites the digits as you press them. 4.9 Local Voice Mute 4.9.1 Enable/Disable Local Voice Mute 4.10 Voice Repetitions 41 4.10.1 Programming Voice Repetitions The OMA-P1104 will recite the number programmed. To program Voice Repetitions: 1. Press SET. SET # 4.11 Intercall Time 4.11.1 Programming Intercall Time 43 4.11.2 Interrogating Intercall Time 4.12 Maximum Number of Calls (Max Calls) 44 4.12.1 Programming Max Calls 45 4.12.2 Interrogating Max Calls 4.13 The Clock 4.13.1 Setting the Clock 46 4.13.2 Interrogating for the Current Time 47 4.14 The Security Code 4.14.1 Locking the Keypad 48 4.14.2 Unlocking the Keypad Chapter 5: Alarm Programming 5.1 Input Configuration 50 5.1.1 Programming Input Configuration STATUS 51 5.1.2 Verifying Input Configuration 5.2 Enable/Disable Inputs 5.2.1 Changing Enabled/Disabled Input Status 52 5.2.2 Verifying Enabled/Disabled Input Status 5.3 Input Recognition Time 53 5.3.1 Programming Input Recognition Time 54 5.3.2 Interrogating Input Recognition Time 5.4 Establishing High and Low Temperature Limits 55 5.4.1 Programming Temperature Limits for a Selected Input 56 5.4.2 Disabling Alarm Response to High or Low Temperature 57 5.4.3 Interrogating High and Low Temperature Limits 5.5 Temperature Scale 58 5.6 Temperature Calibration 5.6.1 Programming Temperature Calibration 59 5.6.2 Interrogating Temperature Calibration 5.7 Obtaining Current Temperature 60 5.8 AC Power Monitoring Enable/Disable 5.8.1 Enabling/Disabling the AC Power Alarm 61 5.9 AC Power Failure Recognition Time 5.9.1 Programming Power Failure Recognition Time 62 2. Press RECOGNITION TIME. 5. Press ENTER. The OMA-P1104 responds: Enter seconds. 7. Press ENTER. The OMA-P1104 responds: OK. ENTER 5.10 Sound Alarm Monitoring 5.10.1 Programming Sound Alarm Sensitivity 64 LISTEN TIME SOUND 5. Press ENTER. The OMA-P1104 responds: Enter. TONE PM 5.10.2 Interrogating Sound Sensitivity 5.11High Sound Alarm Enable/Disable 66 5.11.1Changing Enabled/Disabled High Sound Alarm 5.12 Exit Delay Page Page 69 Chapter 6: Acknowledgment, Status Report, and Remote Access 6.1 Alarm Acknowledgment 6.1.1 Local Acknowledgment 6.1.2 Touch-ToneTM Acknowledgment Page 6.2 Status Report STATUS 72 6.2.1 Example: Status Report, No Alarms 73 6.2.2 Example: Status Report, Existing Alarms 74 6.2.3 Example: Status Report, Disabled Inputs 75 6.2.4 Battery Condition 6.2.5 Remote Access by Touch-Tone Telephone Page Page Page Appendix A: Troubleshooting 80 Cause Solution Communications / Dial-out: Problem Page 82 Problem Solution Communications / Dial-out: Cause Page Page Page Page Appendix B