Manuals
/
Brands
/
Computer Equipment
/
Computer Hardware
/
Omega
/
Computer Equipment
/
Computer Hardware
Omega
OME-PIO-D144 manual
1
1
53
53
Download
53 pages, 1.84 Mb
www.omega.com
e-mail: info@omega.com
U
ser
’
s Guide
OME-PIO-D144
PCI-Bus
Digital I/O Board
Hardware Manual
Shop online at
Contents
Main
Servicing North America:
USA:
Canada:
For immediate technical or application assistance:
USA and Canada:
OME-PIO-D144
Table of Contents
Page
1. Introduction
1.1 Specifications
1.2 Product Check List
Attention!
2. Hardware configuration
2.1 Board Layout
2.2 I/O Port Location
2.3 Enable I/O Operation
2.4 D/I/O Architecture
2.5 Interrupt Operation
& Active_High. The interrupt signal can be programmed to inverted or non- inverted
Refer to DEMO3.C for source code.
Refer to DEMO4.C for source code.
Page
Page
2.6 Daughter Boards
2.6.1 OME-DB-37
2.6.2 OME-DN-37 & OME-DN-50
2.6.3 OME-DB-8125
2.6.4 OME-ADP-37/PCI & OME-ADP-50/PCI
2.6.5 OME-DB-24P/24PD Isolated Input Board
2.6.6 OME-DB-24R/24RD Relay Board
2.6.7 OME-DB-24PR/24POR/24C
2.6.8 Daughter Board Comparison Table
2.7 Pin Assignment
All signals are TTL compatible.
Page
3. I/O Control Register
3.1 How to Find the I/O Address
Vendor ID = 0xE159 Device ID = 0x0002 (0x0001 for Rev 4.0 or above)
Sub-Vendor ID= 0x80 (0x5C80 for Rev 4.0 or above) Sub-Device ID = 0x01 Sub-Aux ID = 0x00
Page
3.1.1 PIO_DriverInit
3.1.2 PIO_GetConfigAddressSpace
3.1.3 Show_PIO_PISO
3.2 The Assignment of I/O Address
Page
3.3 The I/O Address Map
3.3.1 RESET\ Control Register
3.3.2 AUX Control Register
3.3.3 AUX data Register
3.3.4 INT Mask Control Register
3.3.5 Aux Status Register
3.3.6 Interrupt Polarity Control Register
Refer to Sec. 2.5 for more information. Refer to DEMO5.C for more information.
3.3.7 Read/Write 8-bit data Register
3.3.8 Active I/O Port Control Register
Refer to Sec. 2.2 for I/O port location.
3.3.9 I/O Selection Control Register
Refer to Sec. 2.2 for I/O Port Location.
4. Demo Program
4.1 OME-PIO-D144.H
4.2 Demo1: Use D/O of CN1
Page
4.3 Demo2: Use D/O of CN1~CN6
Page
4.4 Demo3: Interrupt demo1
Refer to Sec. 2.5.1 for more information.
4.5 Demo4: Interrupt demo2
Refer to Sec. 2.5.2 for more information.
4.6 Demo5: Interrupt demo3
Page
Page
4.7 DEMO 6: Outport of CN1-CN6
Page
4.8 Demo10: Find Card Number
Page
WARRANTY/DISCLAIMER
RETURN REQUESTS/INQUIRIES
M4037/0104
Where Do I Find Everything I Need for Process Measurement and Control? OMEGAOf Course!
Shop online at www.omega.com
TEMPERATURE
PRESSURE, STRAIN AND FORCE
FLOW/LEVEL
pH/CONDUCTIVITY